-
121
-
122
A study on laser engraving process parameters and performance characteristics for wood base materials
Published 2018“…This research presents a study on the parameter of laser engraving on pine wood and WPC materials by using EleksMaker Laser A5-Pro model with low diode laser (500Mw, 405nm wavelength). …”
Get full text
Get full text
Get full text
Thesis -
123
-
124
Characterization of flow rate and Heat Loss in Heating, Ventilation and Air Conditioning (HVAC) Duct System for Office Building
Published 2021“…The round duct design gives the lowest velocity and head loss in HVAC system approximately around 9.35% as compared to rectangular duct at 0.06 inches thickness. Hence, the trends of the head loss and duct thickness has influenced in reducing noise in HVAC duct system in order to select the best design concepts which is round shape design.…”
Get full text
Conference or Workshop Item -
125
Determination of concentration of Zn, Cu, Cd and Pb in Scylla serrata (Forsskal 1775) from Sungai Penor, Kuantan
Published 2010Get full text
Proceeding Paper -
126
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
127
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
128
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
129
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
130
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
131
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
132
برنامج تدريب معلمي اللغة العربية : " معهد بانغي لتدريب المعلمين نموذجا "
Published 2008Get full text
Proceeding Paper -
133
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
134
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
135
Smoker desaturation during general anaesthesia: a case report
Published 2009“…We excluded other cause of desaturation for example secretion, bronchospasm and also airway obstruction inn this case. We conclude that smoking cessation was necessary at long as possible even though in case of emergency to prevent potential hypoxaemia pre intubation and during extubation at the end of operation. …”
Get full text
Proceeding Paper -
136
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
137
"Personal @ business" businesses'/companies' assets as matrimonial property; the legal policy
Published 2010Get full text
Proceeding Paper -
138
-
139
Biotar ironmaking using wooden biomass and nanoporous iron ore
Published 2009“…In our experiments, three types of iron ores containing different amounts of combined water (CW; 1.6, 3.8, and 9.0 mass %) were first dehydrated at 450 °C to make them porous and then heated with pine tree biomass at 500-600 °C for the gasification and the tar vapor generated was decomposed to deposit carbon within/on the porous ores. …”
Get full text
Article -
140
Development of coated peanut separator and frying skillet machine
Published 2018“…The groundnut is sticking and become like a ping pong size ball and the time consuming to fry is longer. …”
Get full text
Article