-
181
LL5 directs the translocation of Filamin A and SHIP2 to sites of phosphatidylinositol 3,4,5-triphosphate (PtdIns(3,4,5)P3) accumulation, and PtdIns(3,4,5)P3 localization is mutuall...
Published 2010“…Because F-actin initially polymerizes near the plasma membrane, it is likely that membrane-recruited Filamin A efficiently cross-links newly polymerized F-actin, leading to enhanced lamellipodium formation at the site of PtdIns(3,4,5)P3 accumulation. …”
Get full text
Article -
182
-
183
-
184
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…Alumina ball of 3 mm diameter was used as pin, while the cast sample served as the disk. The tests were carried out at a normal load of 5.0 N and a sliding velocity of 250 mm/s for 30 min. …”
Get full text
Article -
185
-
186
-
187
Isolation and characterisation of thermophilic bacterial isolates producing L-asparaginase
Published 2016“…Phenol red at acidic is yellow which might change colour to pink when it is at alkaline. Thus, it indicates the formation of pink zone around microbial colonies producing L-asparaginase. …”
Get full text
Book Chapter -
188
Minutes of meeting. 2 February 1981
Published 1981“…Typewritten on a sheet of pink paper.…”
Get full text
Minutes -
189
Development of coated peanut separator and frying skillet machine
Published 2018“…The groundnut is sticking and become like a ping pong size ball and the time consuming to fry is longer. …”
Get full text
Article -
190
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…The metasurface layer is a lattice pattern of square framed rhombus ring shaped unit-cells that are interconnected by PIN photodiodes. The metasurface layer essentially acts like a superstrate when exposed to RF/microwave radiation. …”
Get full text
Get full text
Article -
191
A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
Published 2011“…Tool life sharply reduced for all the carbide tools while increasing cutting speed twice (from 500m/min to 1000m/min) during machining cast iron. Though the productivity would be double at the speed of 1000m/min than that at the speed of 500m/min, tool wear increases to a few times which indicates that the inserts used are not suitable for machining at a high speed like 1000m/min. …”
Get full text
Book Chapter -
192
Empirical analysis of rough set categorical clustering techniques based on rough purity and value set
Published 2017“…The recent techniques such as Information-Theoretic Dependency Roughness (ITDR), Maximum Dependency Attribute (MDA) and Maximum Significance Attribute (MSA) outperformed their predecessor approaches like Bi-Clustering (BC), Total Roughness (TR), Min-Min Roughness (MMR), and standard-deviation roughness (SDR). …”
Get full text
Get full text
Thesis -
193
Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
Published 1998“…A study has been made on the wear and fiction of hardened AISI 1045 steel using a pi-pin-ondisc type of fiction and wear apparatus. During the investigation the linear pin wear, coe@cient of friction and rise in pin specimen temperature were monitored and wear and fiction curues 'plotted. …”
Get full text
Article -
194
Foam replicated porous 316l stainless steel based on taguchi method for biomedical applications
Published 2018“…The optimised porosity of porous SS316L prepared by ball milling method was 85.44% and achieved using sintering time of 60 minutes, sintering temperature of 1200C, heating rate of 1C/min, SS316L composition of 60 wt% and cooling rate of 1C/min. …”
Get full text
Thesis -
195
A review on safety practices at construction site
Published 2012“…Based on the review, there are ten safety practices found, i.e, safety policy, education and training, safety inspection and safety auditing, safety meeting, supervision, pink tickets, red and green zone demarcation, personal protective equipment (PPE), emergency support and safety measuring device and fall protection systems.…”
Get full text
Proceeding Paper -
196
Why Islamic legal system needs a shift
Published 2011“…Although there had been much change, public criticisms still abound, and removing negative perceptions of the Islamic legal system requires consistent and concerted effort. IF a pink elephant is in a room with us, can we pretend it does not exist or be oblivious to it? …”
Get full text
Article -
197
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
198
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
199
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
200
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis