-
441
Finite element modelling of fixed-fixed end plate attached with vibration absorber
Published 2016“…The present paper investigated the effect of the lightweight dynamic vibration absorber (LDVA) to reduce vibration of thin walled structure. The free and forced vibration response of a rectangular thin plate were performed using finite element method. …”
Get full text
Article -
442
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
443
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
444
The investigation of chlorpyrifos (Cpy) detection of PEDOT:PSS‑MXene(Ti2CTX)‑BSA‑GO composite using P‑ISFET reduction method
Published 2023“…This is much lower than that when using titanium dioxide (TiO2), which is −1.5 V. Composite thin flms containing Ti2CTX MXene are found to detect Cpy with higher sensitivity compared to thin flms without MXene. …”
Get full text
Article -
445
Nutritional status of school children aged 6-10 years old in Selangor
Published 2010“…About 11% of the rural school children were within thin and very thin compared to urban school children 6.5%. …”
Get full text
Article -
446
Nanoparticle-coated Vivaldi antenna array for gain enhancement
Published 2023“…This is achieved by loading the antenna with Complementary Split Ring Resonators (CSRR) and periodic array of open loop meander-line unit cells. The unit cells are designed to exhibit properties of anisotropic zero-index metamaterial (AZIM) over a frequency range of the antenna. …”
Get full text
Get full text
Article -
447
Laser-induced plasma and its applications
Get full text
Book Section -
448
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
449
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
450
Development of a low cost lapping process
Published 2009“…Therefore the understanding of lapping process is very essential for economic manufacture and process improvement of thin silicon chips. A low cost lapping process has been developed, the process tried out on thin silicon chips that generated damage-free with a mirror-like surfaces of low roughness values and reasonably high degree of flatness.…”
Get full text
Proceeding Paper -
451
Manufacture of cylinders with axial imperfections
Published 2004“…The report outlines the methodology and procedures used to manufacture the thin walled cylinder with its axial imperfections using a NUM 1060 CNC Lathe machine. …”
Get full text
Thesis -
452
Development of low coast atmospheric pressure plasma jet for nano and bio technology applications
Published 2018“…The wettability of Aluminium (Al) thin film was enhanced from 72° to 0°. The topography studies indicated that treated Al thin film surface roughness reduced by 2.86 X10-3 nm but the grain size was unaffected. …”
Get full text
Get full text
Get full text
Thesis -
453
Development of portable solar generator
Published 2015“…By using bypass diodes in the cell circuits and by orienting the lens focal line and cell circuit East and West, the smaller 12 W and 36 W units can be easily aimed at the sun and they will then maintain output without adjustment for 2 hours in the middle of a sunny day. …”
Get full text
Get full text
Get full text
Thesis -
454
-
455
Development of an economical lapping process
Published 2012“…This paper presents the development of a low cost lapping process, the process tried out on thin silicon chips that generated fracture-free with mirror-like surfaces of low roughness values and reasonably high degree of flatness.…”
Get full text
Article -
456
The optical properties of oxide films on copper and copper alloys
Published 1985“…Suitable conditions were selected to allow thin, thermal oxide films consisting of cuprous oxide only to be grown on copper and dilute copper alloy substrates. …”
Get full text
Thesis -
457
On phase separation points for one-dimensional models
Published 2009“…In the paper, the one-dimensional model with nearest-neighbor interactions In, n ∈ Z, and the s pin values ±1 is considered. It is known that, under some conditions on parameters of In, a phase transition occurs for this model. …”
Get full text
Article -
458
Measurement and modelling of operational amplifier power supply rejection
Published 1995“…Measured results for 741 and pin-compatible operational amplifiers are tabulated. …”
Get full text
Article -
459
Investigation on plasma properties for deposition of titanium nitride film using reactive magnetron sputtering system
Published 2018“…However, formation of TiN thin flms in nano size device using the plasma sometimes is not stable and hard to achived with optimum level. …”
Get full text
Get full text
Get full text
Thesis -
460
Features of EDM of mild steel with Ta-Cu powder compacted electrodes
Published 2011“…On the contrary, there will be only a very thin layer of material from electrode will be deposited on the workpiece surface when using pure copper electrode. …”
Get full text
Book Chapter