INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS by Amin, A. K. M. Nurul, Konnek, Mohammed

“…It was found from the optimization that, minimum surface roughness and minimum tool wear in the experiment without heat assistance obtained at 41,000 rpm of spindle speed, feed rate of 7.12 mm/min and low depth of cut 5 µm. On the other hand, the suggested conditions for minimum surface roughness and tool wear in heat assisted machining were: spindle speed 38,000 rpm, feed rate 20 mm/min and depth of cut 50 µm. …”
Get full text

Experimental analysis and comparison of performance characteristics of catalytic converters by Mohiuddin, A. K. M.

“…The purpose of this chapter is to present the results of an experimental study of the performance and conversion efficiencies of ceramic monolith three-way catalytic converters (TWCC) employed in automotive exhaust lines for the reduction of gasoline emissions. Two ceramic converters of different cell density, substrate length, hydraulic channel diameter and \vall thickness were studied to investigate the effect of varying key parameters on conversion efficiencies and pressure drop. …”
Get full text

How to assess ankle osteoarthritis: comparison of the Kellgren and Lawrence scale with functional outcome and digital image analysis by Holzer, Nicolas, Salvo, Davide, Marijnissen, Anne Karien, Che Ahmad, Aminudin, Sera, Emanuele, Hoffmeyer, Pierre, Lübbeke Wolff, Anne, Assal, Mathieu

“…Functional outcome was assessed with the AOFAS Hindfoot score. Bone density and minJSW were measured using a previously validated Ankle Image Digital Analysis software (AIDA). …”
Get full text

Cultivation of nannochloropsis sp. for biodiesel production via microwave irradiation direct transesterification using ionic liquid by Wahidin, Suzana

Get full text

Contemporary Islamic educational discourse and the philosophy of empowerment by Rahath House, Yousef, Hashim, Rosnani

“…We suggest that empowerment should be viewed as a social process that helps people gain control over their lives by enabling them to act on issues important to them. …”
Get full text

Ultrasound-assisted extraction of valuable compounds from winter melon (Benincasa hispida) seeds by Sarker, Md. Zaidul Islam

“…Effects of amplitude (25-75%), temperature (40-60°C) and sonication time (20-60 min) on crude extraction yield (CEY) and radical scavenging activities (RSA, % inhibition of DPPH˙ and ABTS˙+ free radicals) of extracts were determined using complete randomised design (CRD). …”
Get full text

High performance liquid chromatographic method for Iso-a-Acids by Khatib, Alfi, Kim, Hye Kyong, Wilson, Erica G., Verpoorte, Robert

“…The mobile phase contains acetonitrile-water- H3PO4 (50 : 50 : 0.01, v/v/v) and is used with a Phenomenex Hypersil 5 m C18 column 250 � 4.6 mm, flow rate 1.5mL/min. Baseline separation of all 6 isomers was achieved with a total run time of 25 min. …”
Get full text

Microstructure and tensile properties of friction stir processed Al-Si alloy by Abdulmalik, Samir Sani, Ahmad, Rosli, Usman, O Y

“…Samples were subjected to FSP using fixed tool rotation speed 1400 rpm and traverse speed 42 mm/min, with tool angle tilted 3˚.The influence of the FSP on the microstructure and tensile properties of the cast AlSi-Cu-Ni alloy samples were studied. …”
Get full text

The depth structure of a London high street : a study in urban order by Clossick, Jane

“…Depth has a number of components: architecture, space and time; depth is the armature in which people live their social lives, and the place where local cultures emerge. …”
Get full text

Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools by Mohamed Ariff, Tasnim Firdaus, Sabiyah, Mohamad Yazid, Adam, Mohd Amirul, Nor, Mohd Anuar

“…The optimum cutting parameters for machining T6061 Aluminium alloy using TiCN coated tool is found; 333 m/min (water based) and 415 m/min (palm oil) at a depth of cut of 0.4 mm and feed rate of 0.6 mm/rev.…”
Get full text

A comparative study of the effectiveness of β-glucosidase immobilized on CNT-nanoparticles and Ca-alginate beads by Jameel , Ahmad Tariq, Mahmood, Labiba, Yusof, Faridah

“…The Michaelis constants, Km and Vmax, determined using Langmuir linearized plot are respectively 0.09048 μmol/mL and 0.00989 μmol/mL.min for immobilized Ca-alginate; and 0.0985 μmol/mL and 0.01237 μmol/mL.min for immobilized MWCNT. …”
Get full text
Get full text

Multi-response optimizations for high speed ductile mode machining of soda lime glass by Bagum, Nasima, Amin, A. K. M. Nurul, Konneh, Mohamed, Mohd Zaib, Noor Fathiah

“…Obtained results demonstrated that optimal combination of the response parameters, 0.78 μm Ra, 107 μm (Tw) and 0.56 min (Tl) were achieved with maximum desirability 77%, at the lowest depth of cut 20 μm at spindle speed of approximately 40000 rpm with feed rate of 69 mm/min.…”
Get full text
Get full text

Applying liquisolid technique to enhance curcumin solubility: a central composite design study by Aghajanpour, Sareh, Yousefi Jordehi, Shabnam, Farmoudeh, Ali, Negarandeh, Reza, Lam, Matthew, Ebrahimnejad, Pedram, Nokhodchi, Ali

“…Experimental results confirmed the formulation’s effectiveness, with a marked reduction in the time to dissolve 63.2% of the drug to 165 min, compared to 300 min for conventional formulations. …”
Get full text

Synthesis of zeolitic imidazolate framework-8 modified graphene oxide composite and its application for lead removal by Ahmad, Siti Zu Nurain, Wan Salleh, Wan Norharyati, Mohd Yusop, Mohd Zamri, Hamdan, Rafidah, Aziz, Farhana, Awang, Nor Asikin, Ismail, Ahmad Fauzi

“…Additionally, ZGH30 achieved the most rapid equilibrium time within 10 min, similar to ZGH50, as compared to their individual components, ZIF-8 (240 min) and GO (300 min). …”
Get full text

Synthesis of zeolitic imidazolate framework-8 modified graphene oxide composite and its application for lead removal by Ahmad, Siti Zu Nurain, Wan Salleh, Wan Norharyati, Mohd Yusop, Mohd Zamri, Hamdan, Rafidah, Aziz, Farhana, Awang, Nor Asikin, Ismail, Ahmad Fauzi

“…Additionally, ZGH30 achieved the most rapid equilibrium time within 10 min, similar to ZGH50, as compared to their individual components, ZIF-8 (240 min) and GO (300 min). …”
Get full text

Kaedah pengajaran yang diamalkan oleh tenaga pengajar di institut memandu by Sulaiman, Shafiza Eliza

“…Data di analisis menggunakan Statistical Package for Social Science (SPSS) versi 22 dengan mencari nilai skor min, ujian t-tidak bersandar dan ujian ANOVA. Hasil analisis mendapati kaedah mengajar dominan yang diamalkan oleh tenaga pengajar di institut memandu adalah kaedah tunjuk cara dengan skor min sebanyak 4.71. …”
Get full text
Get full text
Get full text

Penggunaan modul pembelajaran elektronik (MPE) pengenalan pelancongan H 111 : tinjauan terhadap pensyarah dan pelajar Diploma Pengurusan Pelancongan, Politeknik Johor Bahru by Mohamad, Harulnizam

“…Dalam persoalan kajian pertama, skor min keseluruhan yang diperolehi terhadap penerimaan pelajar ke atas MPE Pengenalan Pelancongan H i l l yang dihasilkan adalah di tahap baik iaitu 3.74. …”
Get full text
Get full text
Get full text

Kemahiran boleh pindah dalam kalangan pelajar kejuruteraan di IPTA by Asha’ri, Aifaa Husna

“…Data dianalisis dengan mencari nilai skor min dan Ujian-t tidak bersandar menggunakan perisian Statistical Package for Social Science (SPSS). …”
Get full text
Get full text

Penyalahgunaan dadah dan kewajaran peruntukan hukuman berat ke atas penagih dan pengedar dadah di Malaysia: satu analisis by Mohd. Noor, Azman

“…Drug abuse has caused a lot of social problems, crimes and wasted many of youth’s lives who are supposed to be the futere asset to the country. …”
Get full text

Cultural factors in traditional Malay house by Abdul Rahim, Zaiton

“…The Malays and their culture are entwined in every aspect of their lives from birth till death. From the pre-Islamic days to gradual Islamic intervention through trading and missionary quests, the culture assimilated left marks in their built environment implicitly and explicitly. …”
Get full text