-
321
Investigation of inductive coupling approach for non-contact bidirectional transfer of power and signal
Published 2012“…The wireless inductive link works as an energy link to power up remote devices and also acts as a communication link to retrieve and write data to the same remote device by using the same set of inductive coils. …”
Get full text
Proceeding Paper -
322
Preliminary analysis on the effect of rain attenuation on Free Space Optics (FSO) propagation measured in tropical weather condition
Published 2011“…However, since the transmission medium of FSO is atmosphere, atmospheric scattering is the major cause for interruption of FSO link. In temperate region, fog is the main factor that affects the availability of the link. …”
Get full text
Proceeding Paper -
323
-
324
Mitigation technique for rain fade using frequency diversity method
Published 2016“…The main outcome of the research shows that there is negligible effect of rain for 5.8 GHz link whereas it very strong on the 26 GHz link. It was observed 15 dB to 35 dB attenuation during measurement period. …”
Get full text
Get full text
Proceeding Paper -
325
Linear quadratic regulator (LQR) approach for lifting and stabilizing of two wheeled wheelchair
Published 2011“…The equations of motions, which are very complex, are derived from the wheels, Link1 and Link2. The goal is to have both links of the two-wheeled wheelchair to be at the upright position. …”
Get full text
Proceeding Paper -
326
-
327
Smart home control system design using internet of things based energy harvesting technology
Published 2024“…The objective of this research is to provide security for homeowners by facilitating fingerprints and PIN (Personal Identification Numbers) in entering the house, then in the event of a power outage, it activates the function of energy harvesting technology. …”
Get full text
Conference or Workshop Item -
328
Remote operation of CNC milling through virtual simulation and remote dekstop interface
Published 2009“…Capability of remote operation is supported by an auto setup attachment with a reconfigurable pin type setup free technology installed on the table of CNC milling machine to perform unattended machining process. …”
Get full text
Article -
329
Wear behavior of modified surface layer produced by TIG melting of preplaced Ti powder in nitrogen environment
Published 2011“…The wear property of the melt track was investigated using pin-on-disk tribometer at room temperature. The modified surface layer gave a low friction value of 0.12 and wear rate of 0.007895 ×10-4 compared to 1.648 × 10-4 mm3/N/m for the uncoated steel surface.…”
Get full text
Article -
330
A new viscoelastic damper for seismic protection of steel building frame
Published 2024Get full text
Thesis -
331
Aluminium metal matrix composite: improving wear performance through treatment
Published 2011“…The wear test was carried out using a pin-on- disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
332
Microelectrical mechanical systems switch for designing multi-band antenna
Published 2009“…Problem statement: In this study Microelectrical Mechanical System (MEMS) switches were proposed to design a reconfigurable/multi-band antenna to replaced PIN diode switches or semiconductor switches due to lower insertion losses, good isolation, much lower intermodulation distortion, and lower power consumption. …”
Get full text
Article -
333
Recovery of virus producing NDV vaccine by Tangential Flow Filtration (TFF)
Published 2009“…The results revealed that higher pressure input (Pin), lower pressure output (Pout), and higher virus concentration led to higher virus titer. …”
Get full text
Proceeding Paper -
334
Wear properties of Fe-C-Al cast iron and conventional cast iron - a comparative study
Published 2011“…In the present study, the wear test was conducted on both conventional cast iron (CI) and Fe-C-Al cast iron using universal pin-on-disk (POD) machine. The wear track profile and damage surface were characterized using optical profilometer and scanning electron microscopy (SEM) respectively. …”
Get full text
Proceeding Paper -
335
Identifying preface in the Qur’anic Surahs a new methodology of Qur’anic Interpretation”
Published 2014“…Some of them simply tried to show the link among all the verses of Qur’anic Surahs; and some others identified various themes in a Surah and suggested possible link among them. …”
Get full text
Article -
336
The effect of weather on free space optics communication (FSO) under tropical weather conditions and a proposed setup for measurement
Published 2010“…The parameters are used to evaluate link availability of the FSO link. The result of the evaluation can provide more knowledge on the feasibility of FSO deployment under tropical weather condition especially for a long range link.…”
Get full text
Proceeding Paper -
337
Substrate integrated waveguide cavity backed frequency reconfigurable antenna for cognitive radio applies to internet of things applications
Published 2019“…Reconfiguration of frequency bands is achieved using PIN diodes. The antenna resonated at 2.624, 2.664, 2.720, 2.752, 4.304, 4.532, 4.556, 5.236, 5.304, 5.368, 5.332, and 5.392 GHz. …”
Get full text
Article -
338
V-Band fade dynamics characteristics analysis in tropical region
Published 2010“…Approach: Statistics for 20 consecutive months of V band terrestrial link signal attenuation measurements in Malaysia were presented in this analysis. …”
Get full text
Article -
339
The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel
Published 1996“…This was done on three types of cast iron, namely spheroidal graphite, flake graphite and chilled cast iron against a mild steel disc configuration using a pin-on-disc type of friction and wear apparatus. …”
Get full text
Article -
340
Virtual simulation and remote desktop interface for CNC milling operation
Published 2011“…Capability of remote operation is supported by an auto setup attachment with a reconfigurable pin type setup free technology installed on the table of CNC milling machine to perform unattended machining process. …”
Get full text
Article