-
261
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…Alumina ball of 3 mm diameter was used as pin, while the cast sample served as the disk. The tests were carried out at a normal load of 5.0 N and a sliding velocity of 250 mm/s for 30 min. …”
Get full text
Article -
262
-
263
Wear study of Mg-SiCp reinforcement aluminium metal matrix composite
Published 2016“…The pin-on-disc test was also done at room temperature in a dry sliding wear condition. …”
Get full text
Get full text
Article -
264
Influence of single and multiple particle size variation on mechanical and wear behaviour of aluminium silicon carbide composites
Published 2015“…Standard impact and hardness test was conducted to ascertain the energy absorbed before fracture failure and resistance to plastic deformation of the composite. Pin-on-disc test was also investigated at room temperature under dry sliding wear condition. …”
Get full text
Proceeding Paper -
265
Aluminium metal matrix composite: improving wear performance through treatment
Published 2011“…The wear test was carried out using a pin-on- disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
266
Tribological behavior of dual and triple particle size SiC reinforced Al0MMCs: a comparative study
Published 2008“…The wear test was carried out using a pin-on-disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
267
Effect of heating rates on the microstructure and gas permeation properties of carbon membranes
Published 2018“…High performance tubular carbon membrane (TCM’s) for CO2 separation were prepared by controlling the carbonization heating rates in range of 1-7 oC/min carbonized at 800 oC under Argon environment. …”
Get full text
Article -
268
Capabilities of cermets tools for high speed machining of austenitic stainless steel
Published 2006“…In the present work cermet tools coated with titanium nitride were used to turn austenitic stainless steel at speeds between 300 and 700 m min-1. Feed rates were varied between 0.05 to 0.4 mm rev-1. …”
Get full text
Article -
269
Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
Published 1998“…A study has been made on the wear and fiction of hardened AISI 1045 steel using a pi-pin-ondisc type of fiction and wear apparatus. During the investigation the linear pin wear, coe@cient of friction and rise in pin specimen temperature were monitored and wear and fiction curues 'plotted. …”
Get full text
Article -
270
Wear behavior of as-cast and heat treated triple particle size SiC reinforced aluminium metal matrix composites
Published 2009“…The wear test was carried out using a pin-on-disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
271
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
272
-
273
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
274
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
275
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
276
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
277
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
278
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
279
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
280
The use of SEM to investigate the effect of an electron beam on the optically-visible flashover treeing of MgO ceramic
Published 2007“…An SEM may be used not only to observe a surface image but also to provide a fine electron beam for charging an insulator surface simultaneously. …”
Get full text
Article