-
461
Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts
Published 2009“…This paper presents an approach to establish models for tool life in end milling of titanium alloy Ti–6Al– 4V using uncoated carbide inserts under dry conditions. …”
Get full text
Article -
462
-
463
-
464
Environmental, social, and governance (ESG) reporting and missing (M) scores in the Industry 5.0 era: broadening firms’ and investors’ decisions to achieve sustainable development goals
Published 2024“…New or missing (M) scores revealed by I5.0 technologies can assist both investors and company managers.…”
Get full text
Get full text
Article -
465
Simulation of haddad surge arrester model on a 132kV overhead transmission line for back flashover analysis using Alternative Transient Program (ATP)
Published 2015“…This study modelled a 132kV overhead transmission line for back flashover pattern by using ATP/EMTP software before and after implement the Haddad Surge Arrester Model. …”
Get full text
Get full text
Thesis -
466
Comparison of surface roughness in end milling of titanium alloy Ti-6Al-4V using uncoated WC-Co and PCD inserts through generation of models
Published 2011“…There also exists strong adhesion between the tool and workpiece material [2]. Since the performance of conventional tools is poor in machining Ti-6Al-4V, a number of newly evolved tool materials, such as cubic boron nitride (CBN) and polycrystalline diamond (PCD), are being considered to achieve high-speed milling [3]. …”
Get full text
Book Chapter -
467
Tahap kesediaan pelajar menghadapi dunia pekerjaan dalam bidang perakaunan : kajian ke atas pelajar semester akhir Diploma Perakaunan di 5 buah politeknik
Published 2002“…Analisis data dibuat dengan menggunakan perisian SPSS untuk membuat pengiraan peratusan dan min. Keputusan yang diperolehi menunjukkan pelajar-pelajar perakaunan di Politeknik kurang bersedia menghadapi dunia pekeijaan dari segi pengalaman dan kemahiran berbahasa Inggeris. …”
Get full text
Get full text
Get full text
Thesis -
468
-
469
-
470
-
471
-
472
Tool life prediction by response surface methodology in end milling titanium alloy Ti-6A1-4V using uncoated WC-Co inserts
Published 2009“…This paper presents an approach to establish models for tool life in end milling of titanium alloy Ti–6Al– 4V using uncoated carbide inserts under dry conditions. …”
Get full text
Article -
473
IVF-ICSI split insemination reveals those cases of unexplained infertility benefitting from ICSI even when the DNA Fragmentation index is reduced to 15% or even 5%
Published 2016“…Conclusions IVF-ICSI split insemination can reveal those cases which will benefit from ICSI even where semen parameters and DFI are normal; however if the DFI is reduced to a 15% cut-off level, the rate of CFF will be minimized, but not completely excluded, even at 5%..…”
Get full text
Article -
474
-
475
On iterative low-complexity algorithm for optimal antenna selection and joint transmit power allocation under impact pilot contamination in downlink 5g massive MIMO systems
Published 2020“…The proposed low- complexity iterative algorithm achieved the best maximal EE according Fig. 6.5 in chapter 6, which was 95 Mbits/j, resulted from the large number of antennas at the BS, when the transmit power was and transmit antennas was = 100 and user was = 20. …”
Get full text
Get full text
Get full text
Thesis -
476
-
477
-
478
-
479
-
480
Animal care: an Islamic perspective with particular reference to unwanted pets- stray dogs and cats
Published 2016“…Small animals - dogs, and cats have been staying together with people since the beginning of human history. Humans have been receiving numerous benefits from them, such as keeping them as companions, using them for hunting, house keeping, and conducting research studies. …”
Get full text
Article