-
81
Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
Published 1998“…A study has been made on the wear and fiction of hardened AISI 1045 steel using a pi-pin-ondisc type of fiction and wear apparatus. During the investigation the linear pin wear, coe@cient of friction and rise in pin specimen temperature were monitored and wear and fiction curues 'plotted. …”
Get full text
Article -
82
Impact of a reverse delta type add-on device on the flap-tip vortex of a wing
Published 2016“…The effect of interactions of vortices produced by an outboard flap-tip of a half-span wing (NACA 23012 in landing configuration) and a slender reverse delta type add-on device, placed in the proximity of the outboard flap-tip, on the upper surface of the half-span wing is investigated using Particle Image Velocimetry in a closed loop low speed wind tunnel. …”
Get full text
Get full text
Article -
83
Influential factors and structural reliability
Published 2013“…This study focuses on the influential factors that enhance the reliability and versatility of structure throughout the life span. The factors are considered on the basis of the need for assessment of state of –art- structural analysis and design. …”
Get full text
Article -
84
-
85
-
86
Analytical Finite Element Formulation of Non-uniform Euler-Bernoulli Beam
Published 2011“…To satisfy some requirements, it is not uncommon that the beam has to posses a non-uniform distribution of its cross section along the span. A common approach to analyze such a structure is by using a variational principle to develop the element stiffness matrix. …”
Get full text
Proceeding Paper -
87
A review on safety practices at construction site
Published 2012“…Based on the review, there are ten safety practices found, i.e, safety policy, education and training, safety inspection and safety auditing, safety meeting, supervision, pink tickets, red and green zone demarcation, personal protective equipment (PPE), emergency support and safety measuring device and fall protection systems.…”
Get full text
Proceeding Paper -
88
Why Islamic legal system needs a shift
Published 2011“…Although there had been much change, public criticisms still abound, and removing negative perceptions of the Islamic legal system requires consistent and concerted effort. IF a pink elephant is in a room with us, can we pretend it does not exist or be oblivious to it? …”
Get full text
Article -
89
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
90
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
91
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
92
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
93
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
94
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
95
Methodology to develop bottleneck-based heuristic for permutation flow shop scheduling
Published 2020“…This paper proposes a new heuristic that introduces the method of bottleneck-based (BNB) at the beginning of an initial sequence determination with the objective of make span minimization for large size problem. Earlier studies found that the scheduling activity become complicated when dealing with machine, m greater than 2, known as non-deterministic polynomial-time hardness (NP-hard). …”
Get full text
Book Section -
96
-
97
-
98
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
99
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
100
Enlighten architecture students on environmental design through computer simulation
Published 2013Get full text
Get full text
Proceeding Paper