-
361
Keutamaan Solat berjemaah
Published 2010Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
Get full text
Book -
362
Sifat solat nabi s.a.w. (Terjemahan)
Published 2010Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
Get full text
Book -
363
Akhir Ramadan sebagai pengukur jati diri
Published 2009Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
Get full text
Article -
364
Issues in contemporary zakah: a juristic analytical evaluation
Published 2011Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
Get full text
Book -
365
Development of multiplex real-time PCR for the rapid detection of five bacterial causes of community acquired pneumonia
Published 2011“…Duplex and triplex real-time PCR assays were developed using five sets of primers and probes that were designed based on an appropriate specific gene for each of the above CAP pathogens. …”
Get full text
Article -
366
The THD performance of single phase five level inverter using pr and harmonic compensators current controller
Published 2020“…This project is to observe the THD performance of single phase five level inverter using proportional resonant (PR) and harmonic compensators current controller. …”
Get full text
Get full text
Get full text
Thesis -
367
-
368
-
369
Composite Right/Left-Handed Transmission-Line Based Wideband Antenna for WLAN, WiMAX and WiFi Applications
Published 2016“…In this article, a new and compact wideband antenna is presented based on metamaterial composite right/left-handed transmission-line (CRLH-TL) structures. The proposed wideband planar antenna provides enhanced gain performance and is optimized for bandwidth, efficiency and radiation patterns. …”
Get full text
Conference or Workshop Item -
370
Enhancement of machinability by workpiece preheating in end milling of Ti-6Al-4V
Published 2008“…Practical implications: The cost of machining Ti-6Al-4V is extremely high because of the relatively low machining speed and short tool life. …”
Get full text
Article -
371
Novel antenna array configuration using miniature double box branch-line couplers for wideband circularly polarized applications
Published 2023“…This paper presents a wideband circularly polarized (CP) antenna array using a miniaturized double box branch-line coupler. This was achieved by creating a slow wave structure by introducing open-circuit stubs on the inside arms of the branch-line coupler. …”
Get full text
Article -
372
A study of micro to nano structure fine solid line printing for graphene ink by micro-flexographic printing method
Published 2016“…This paper will illustrates the use of graphene in producing multiple fine lines printing capability for the application of printing electronic, graphic and bio-medical.…”
Get full text
Article -
373
Corrugation and Squat Classification and Detection with VGG16 and YOLOv5 Neural Network Models
Published 2024“…This study presents a novel approach utilizing deep learning models, VGG16 and YOLOv5, for detecting and classifying railway track defects, explicitly focusing on corrugation and squat defects. …”
Get full text
Article -
374
Ethyl 1-sec-butyl-2-phenyl-1H-benzimidazole-5-carboxylate
Published 2010“…The dihedral angle between the phenyl and benzimidazole ring system is 43.71 (5)�. The atoms of the butyl group are disordered over two sets of sites with occupancies of 0.900 (4) and 0.100 (4). …”
Get full text
Article -
375
Ethyl 1-(2-hydroxyethyl)-2-phenyl-1H-benzimidazole-5-carboxylate
Published 2010Get full text
Article -
376
Ethyl 1-(2-hydroxyethyl)-2-propyl-1H-benzimidazole-5-carboxylate
Published 2011Get full text
Article -
377
-
378
High‑isolation array antenna design for 5G mm‑wave MIMO applications
Published 2024“…The inter-element isolation exceeds 25 dB, and the array provides a gain greater than 6 dBi, with a peak gain of 7.5 dBi at 39 GHz. This high gain enhances the antenna’s ability to mitigate atmospheric attenuation at higher frequencies, making it highly suitable for 5G mm-wave applications.…”
Get full text
Article -
379
Influence of preheating on chatter and machinability of titanium alloy - Ti6A14V
Published 2005“…The cutting speeds used in these experiments were 40, 80, 120 and 160 m/min; the depths of cut were 1 and 1.5 mm and the feed rates were 0.1 and 0.15 mm/rev. …”
Get full text
Thesis -
380
Roles of 5S practice in MARA Ecosystem Quality Standard (MQS)—a case study
Published 2021“…The practice of 5S has been adopted by many organizations as a method to organize the workplace towards reducing waste and improving productivity. …”
Get full text
Book Section