-
341
Technology transfer - a primary element of sustainable development
Published 2005Get full text
Proceeding Paper -
342
A new technique for the investigation of chatter formation during end milling of medium carbon steel (AISI 45)
Published 2010Get full text
Proceeding Paper -
343
-
344
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
345
Core power control analysis and design for triga nuclear reactor
Published 2023Get full text
Thesis -
346
The mixed spices increase serum adiponectin protein (adipokine) and insulin in STZ induced hyperglycemic rats
Published 2010Get full text
Proceeding Paper -
347
PCR-based chromosome walking: the SFR 3 case
Published 2006“…Eleven new PCR markers had been designed to fine map the gene. Roughly 557 F2 plants tested in these experiments and 38 lines were then used in the fine mapping experiments. …”
Get full text
Article -
348
Legal disputes in determining religious status of a child when one parents converts to Islam under Malaysian law
Published 2009Get full text
Proceeding Paper -
349
Family mediation in Asia: a special reference to the law and practice in Malaysia
Published 2007“…For this purpose the practice in Singapore, China, Japan and Hong Kong is described. However the focus of the article is the law and practice of conciliation in Malaysia which are governed by the Law Reform (Marriage and Divorce) Act, 1976. …”
Get full text
Article -
350
-
351
ARCASIA architectural timeline chart : Malaysia
Published 2006“…Bangladesh, China, Hong Kong, India,Indonesia, Japan, Korea, Macau,Malaysia, Mongolia,Nepal, Pakistan,Philippines, Singapore,Sri Lanka, Thailand, Vietnam. …”
Get full text
Book -
352
-
353
AI-powered COVID-19 forecasting: a comprehensive comparison of advanced deep learning methods
Published 2024“…Bayesian optimization was also implemented to fine-tune these models. Results: The evaluation framework revealed that each model exhibited different levels of predictive accuracy and precision. …”
Get full text
Article -
354
AI-powered COVID-19 forecasting: a comprehensive comparison of advanced deep learning methods
Published 2024“…Bayesian optimization was also implemented to fine-tune these models. Results: The evaluation framework revealed that each model exhibited different levels of predictive accuracy and precision. …”
Get full text
Article -
355
Wideband and multiband antennas for multi-configuration mode applications
Published 2023Get full text
Thesis -
356
Physico-mechanical properties of polymer concrete containing micro-filler of palm oil fuel ash
Published 2018“…Objective of this study is to present a research conducted on ground (fine) and unground (coarse) POFA in polymer concrete (PC) followed by determination on the physico-mechanical properties of PC. …”
Article -
357
Bitumen modification using oil palm fruit ash for stone mastic asphalt
Published 2024Get full text
Thesis -
358
On phase separation points for one-dimensional models
Published 2009“…In the paper, the one-dimensional model with nearest-neighbor interactions In, n ∈ Z, and the s pin values ±1 is considered. It is known that, under some conditions on parameters of In, a phase transition occurs for this model. …”
Get full text
Article -
359
Measurement and modelling of operational amplifier power supply rejection
Published 1995“…Measured results for 741 and pin-compatible operational amplifiers are tabulated. …”
Get full text
Article -
360
Influence of mesh sizes and orientations on expanded aluminium sheets on tensile performances
Published 2022“…According to the results of the experiment, specimens with fine mesh have higher tensile stress, which is 44.90 MPa for fine mesh specimens with a 30° orientation, compared to medium and coarse mesh sizes, which have the lowest strength, which is 7.06 MPa for coarse mesh specimens with a 60° orientation. …”
Get full text
Conference or Workshop Item