-
301
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
302
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
303
-
304
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
305
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
306
-
307
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
308
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
309
-
310
-
311
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
312
Pretreatment of sludge palm oil by ultrasonic energy for biodiesel production
Published 2010“…The reduction of free fatty acids (FFAs) in sludge palm oil (SPO) was measured at different sonication time from 30 to 300 min and the optimum time was determined. It is reasonable to indicate that the pretreatment of SPO by applying ultrasonic energy is related to long sonication time. …”
Get full text
Proceeding Paper -
313
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
314
Novel opto-electronic and plastic fibre sensors
Published 1998“…Experimental results obtained confirm the long and linear operational range of the sensor (between 15 mm and 90 mm for a mirror target and between 20 mm and 100 mm for a matt white paper target). …”
Get full text
Thesis -
315
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
316
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
317
Simultaneous extraction and fractionation of pufa from tropical tuna (thunnus tongol) head using pressure swing technique of supercritical CO2 (SC-CO2)
Published 2012“…The dry and grinded sample was pressurised with pure CO2 and then soaked in the vessel for 1 hrs, and extracted continuously for 20 min at optimal conditions of 35 MPa, 65 oC, 3 ml min-1. …”
Get full text
Proceeding Paper -
318
Dry machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
Published 2013“…In metal cutting process, the use of cutting fluids, cooling and easy chip removal causes long-term effects of cutting fluids disposal into environment. …”
Get full text
Article -
319
Risk of Escherichia coli O157:H7 transmission linked to the consumption of raw milk
Published 2013Get full text
Article -
320
Cost-aware real-time divisible loads scheduling in cloud computing
Published 2024Get full text
Thesis