-
181
Minutes of meeting. 2 February 1981
Published 1981“…Typewritten on a sheet of pink paper.…”
Get full text
Minutes -
182
-
183
Development of coated peanut separator and frying skillet machine
Published 2018“…The design convenient, determination of the material selection and the main components that help to operate the machine are the main aspects have been considered. …”
Get full text
Article -
184
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
185
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. …”
Get full text
Get full text
Article -
186
A New Design and Simulation of Smart Sensing for Emergency Vehicle
Published 2024“…The sensor can detect the sound of emergency vehicles and respond immediately to them by signalling smaller parallel visitors to change the screen from pink to green or vice versa. Therefore, this flow reduces the travel time required for emergencies.…”
Get full text
Article -
187
Dynamic duty cycle mechnism for mobility in wirless sensor networks
Published 2020“…Done through two diverse scenarios that are the sink and the sensor nodes fixed, and the sink nodes and the nodes are the mobility that occurs. …”
Get full text
Get full text
Get full text
Thesis -
188
The effect of pre-processing techniques and optimal parameters on BPNN for data classification
Published 2015“…In this research, a performance analysis based on different activation functions; gradient descent and gradient descent with momentum, for training the BP algorithm with pre-processing techniques was executed. The Min-Max, Z-Score, and Decimal Scaling Normalization pre-processing techniques were analyzed. …”
Get full text
Get full text
Get full text
Thesis -
189
A New Design and Simulation of Smart Sensing for Emergency Vehicle
Published 2024“…The sensor can detect the sound of emergency vehicles and respond immediately to them by signalling smaller parallel visitors to change the screen from pink to green or vice versa. Therefore, this flow reduces the travel time required for emergencies.…”
Get full text
Article -
190
Joint routing protocol and image compression algorithm for prolonging node lifetime in wireless sensor network
Published 2018“…The conventional data routing protocols do not consider the power available at the node on the path from source to sink, thus they result in the exhaustion and eventual death of nodes surrounding the sink node, thus generating routing holes reducing the network throughput. …”
Get full text
Get full text
Get full text
Thesis -
191
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
192
MHD stagnation flow of nanofluid past a permeable shrinking surface with various conditions
Published 2018“…The purpose of the present study is to analyze the effects of slip and heat source/sink on magnetohydrodynamic stagnation-point flow and heat transfer past a permeable shrinking surface with convective boundary condition. …”
Get full text
Get full text
Get full text
Thesis -
193
Preparation of injection moulding processing for high density polyethylene via moldflow advisor 2015 simulation
Published 2018“…Both simulation and practical results have no sink marks. Therefore, it can be concluded that the simulation process had provided a good prediction for practical injection moulding preparation. …”
Article -
194
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
195
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
196
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…This consists of a densely crossllnked core of mainly diester crosslinks, surrounded by a less densely crosslinked network containing more ether crosslinks. …”
Get full text
Thesis -
197
Radiative MHD Boundary Layer Flow and Heat Transfer Characteristics of Fe-Casson Base Nanofluid over Stretching/Shrinking Surface
Published 2024“…This paper considers the MHD boundary layer flow and heat transfer characteristics of FeCasson-based nanofluid over an exponentially stretching/shrinking surface, including heat source/sink and Newtonian heating effects. In this regard, to develop the system of the governing equations, the one phase model named as Tiwari and Das model is considered with iron nanoparticles. …”
Get full text
Article -
198
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
199
-
200
Smart home control system design using internet of things based energy harvesting technology
Published 2024“…The objective of this research is to provide security for homeowners by facilitating fingerprints and PIN (Personal Identification Numbers) in entering the house, then in the event of a power outage, it activates the function of energy harvesting technology. …”
Get full text
Conference or Workshop Item