-
501
How to assess ankle osteoarthritis: comparison of the Kellgren and Lawrence scale with functional outcome and digital image analysis
Published 2012“…Functional outcome was assessed with the AOFAS Hindfoot score. Bone density and minJSW were measured using a previously validated Ankle Image Digital Analysis software (AIDA). …”
Get full text
Article -
502
-
503
-
504
-
505
Isolated facial palsy due to intra-aural tick (ixodoidea) infestation
Published 2007Get full text
Article -
506
Removal of extensive maxillary dentigerous cyst via a Caldwell-Luc procedure
Published 2008Get full text
Article -
507
-
508
Mas Cotek (Ficus deltoidea): a possible supplement for Type II Diabetes: (a pilot study)
Published 2011Get full text
Book Chapter -
509
Providing feedback for students' drafts in academic writing: can developmental Rubric do the trick?
Published 2015“…Teachers were able to specifically pin-point the areas where students needed to improve their academic writing. …”
Get full text
Proceeding Paper -
510
Formation of Fe-C-Si ternary composite coating on CP-titanium and its tribological interaction with Jatropha oil
Published 2016“…The wear behavior of coated CP-titanium was performed using pin-on-disk machine at room temperature under Jatropha-biodiesel lubricated condition. …”
Get full text
Proceeding Paper -
511
A Novel MIMO antenna integrated with a solar panel and employing AI-equalization for 5G wireless communication networks
Published 2024“…We demonstrate that the directivity of this antenna array can be precisely electronically reconfigured using PIN diode switches. Additionally, we show the feasibility of integrating solar panels with the proposed MIMO antenna array. …”
Get full text
Get full text
Article -
512
Design of microstrip ultra wide band antenna with two notch filters for wireless communication
Published 2015“…In order to add reconfigurable characteristics to the patch antenna, two copper strips are putted on the slots to represent the ON and OFF switching status of an ideal Pin diode. By using this simple switching technique, the current distribution of the patch changes and enables the antenna to have four modes of operation. …”
Get full text
Get full text
Get full text
Thesis -
513
Theoretical analysis of photoparametric amplifier
Published 2010“…The second method is to use Optiwave software in implement is the photo parametric amplifier circuit. Photo diode PIN type has been used to detect any coming signal at the receiver circuit. …”
Get full text
Get full text
Get full text
Thesis -
514
Ultrasound-assisted extraction of valuable compounds from winter melon (Benincasa hispida) seeds
Published 2013“…Effects of amplitude (25-75%), temperature (40-60°C) and sonication time (20-60 min) on crude extraction yield (CEY) and radical scavenging activities (RSA, % inhibition of DPPH˙ and ABTS˙+ free radicals) of extracts were determined using complete randomised design (CRD). …”
Get full text
Article -
515
High performance liquid chromatographic method for Iso-a-Acids
Published 2006“…The mobile phase contains acetonitrile-water- H3PO4 (50 : 50 : 0.01, v/v/v) and is used with a Phenomenex Hypersil 5 m C18 column 250 � 4.6 mm, flow rate 1.5mL/min. Baseline separation of all 6 isomers was achieved with a total run time of 25 min. …”
Get full text
Article -
516
Microstructure and tensile properties of friction stir processed Al-Si alloy
Published 2018“…Samples were subjected to FSP using fixed tool rotation speed 1400 rpm and traverse speed 42 mm/min, with tool angle tilted 3˚.The influence of the FSP on the microstructure and tensile properties of the cast AlSi-Cu-Ni alloy samples were studied. …”
Get full text
Article -
517
Fatty acid composition of Malaysian giant mudskipper (Periophthalmodon schlosseri) fish oil
Published 2010“…An HP-5 non-polar capillary column was used and the temperature was initially kept at 50oC for 2 min and then programmed at 5oC min-1 to 250oC. …”
Get full text
Get full text
Get full text
Proceeding Paper -
518
Eco-friendly machining of T6061 aluminium alloy using titanium carbonitride (TiCN) coated tools
Published 2012“…The optimum cutting parameters for machining T6061 Aluminium alloy using TiCN coated tool is found; 333 m/min (water based) and 415 m/min (palm oil) at a depth of cut of 0.4 mm and feed rate of 0.6 mm/rev.…”
Get full text
Article -
519
A comparative study of the effectiveness of β-glucosidase immobilized on CNT-nanoparticles and Ca-alginate beads
Published 2014“…The Michaelis constants, Km and Vmax, determined using Langmuir linearized plot are respectively 0.09048 μmol/mL and 0.00989 μmol/mL.min for immobilized Ca-alginate; and 0.0985 μmol/mL and 0.01237 μmol/mL.min for immobilized MWCNT. …”
Get full text
Get full text
Proceeding Paper -
520
Multi-response optimizations for high speed ductile mode machining of soda lime glass
Published 2015“…Obtained results demonstrated that optimal combination of the response parameters, 0.78 μm Ra, 107 μm (Tw) and 0.56 min (Tl) were achieved with maximum desirability 77%, at the lowest depth of cut 20 μm at spindle speed of approximately 40000 rpm with feed rate of 69 mm/min.…”
Get full text
Get full text
Article