-
341
Preschoolers fast map and retain artifact functions as efficiently as artifact names, but artifact actions are the most easily learned
Published 2018“…Participants performed well on comprehension tests of all three kinds of information. In Experiment 2, 3-year-olds (N = 100) were exposed to these three kinds of information only once. …”
Get full text
Article -
342
Effect of poly(ethylene glycol) on the injectability, setting behavior and mechanical properties of calcium phosphate bone cement
Published 2018“…Simen tanpa PEG mempunyai masa pengerasan awal daripada 3 min kepada 122 min dan masa pengerasan akhir daripada 5 min kepada 277 min. …”
Get full text
Get full text
Get full text
Article -
343
-
344
Foam replicated porous 316l stainless steel based on taguchi method for biomedical applications
Published 2018“…The optimised porosity of porous SS316L prepared by ball milling method was 85.44% and achieved using sintering time of 60 minutes, sintering temperature of 1200C, heating rate of 1C/min, SS316L composition of 60 wt% and cooling rate of 1C/min. …”
Get full text
Thesis -
345
-
346
Optimization of activated carbon production from empty fruit bunch fibers in one-step steam pyrolysis for cadmium removal from aqueous solution
Published 2011“…Physical activation comprised of carbonization for 30 min using nitrogen gas (N2), followed by activation with steam at different flow rates (2.0, 3.0, and 4.0 ml/min), temperatures (600, 750,and 900�C) and times (15, 30, and 45 min). …”
Get full text
Article -
347
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. …”
Get full text
Get full text
Article -
348
Characterisation of surface texture using AFM with trimmed probe tip
Published 2006“…A comparison of the scanning results with analytical calculation showed that the trimmed tips were superior in imaging the profile for both the hole shaped and pin shaped microfeatures. But when using the trimmed high aspect ratio tip, the scanning speed was significantly low. …”
Get full text
Article -
349
Distraction osteogenesis over intramedullary nail : a report of two cases
Published 2006“…The healing index was 19.5 days/cm and 14.8 days/cm respectively, compared favorably to 30 days/cm with traditional method of distraction osteogenesis. There were mild pin tract infections and joint stiffness which responded to non-operative treatment.…”
Get full text
Article -
350
-
351
Alternative sweetener from curculigo fruits
Published 2020“…Finally, the dried fruits were blended in order to get a fine powder. Curculin is a sweet protein with a taste-modifying activity of converting sourness to sweetness. …”
Get full text
Book Section -
352
Effect of river indus sand on concrete tensile strength
Published 2018“…In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. …”
Get full text
Article -
353
Response and inaccuracy issues of sensors
Published 2011“…In recent years, many kinds of sensors are used to get the response of various parameters such as pressure, speed, temperature, etc. …”
Get full text
Book Chapter -
354
A study on abrasive water jet machining of aluminum with garnet abrasives
Published 2005“…The feed rate of the work should be kept within 40 rum min- I (at the jet pressure of 30 h i and the stand-off distance of3 mm). because a feed rate beyond 40 mm min-I results in sharp increase in taper angle. …”
Get full text
Article -
355
Adsorption behaviour of manganese (Mn2+) removal from aqueous solution using carbon nanotubes
Published 2010“…Different pHs are pH 6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg, 6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min, 55 min, 87.5 min and 120 min while the agitation speeds are 100rpm, 150rpm, 200rpm, 250rpm and 300rpm. …”
Get full text
Proceeding Paper -
356
Efficacy of Malaysian plant extracts in preventing peroxidation reactions in model and food oil systems
Published 2004“…This was followed by the extracts of limau purut leaves (85 min), peels (60 min), and stems (39 min). The antioxidative activities of these plants, however, were lower than those of rosemary and sage. …”
Get full text
Article -
357
Effects of flux application and melting parameters in investment casting of pure aluminium by in-situ melting technique
Published 2018“…The aluminium granules then were heated at the temperature of 850oC for 30 min in argon environment at the flow rate of argon gas 0.5, 2.5 and 5 l/min to reduce the oxidation of the aluminium granules. …”
Get full text
Thesis -
358
Trunk-enabled toys
Published 2016“…This work explores the use of technology to help create different kinds of interfaces for controls aimed at captive elephants, enabling them to interact with digitally enhanced playful systems (smart toys). …”
Get full text
Conference or Workshop Item -
359
Kesan pembelajaran berasaskan masalah terhadap motivasi pelajar dalam mata pelajaran kemahiran hidup
Published 2014“…Namun begitu, nilai skor min motivasi keseluruhan Kumpulan Rawatan adalah lebih tinggi daripada Kumpulan Kawalan. …”
Get full text
Get full text
Get full text
Thesis -
360
Oxidative behaviour of four Malaysian edible plant extracts in model and food oil systems
Published 2012“…This was followed by the extracts of Chinese cabbage (80 min), “kucai” (60 min), and “kesom” (40 min). The antioxidative activities of these plants, however, were lower than those of rosemary and sage. …”
Get full text
Article