-
641
Olahan air sisa pusat penyembelihan ayam menggunakan elektrod keluli tahan karat dan aluminum melalui proses gabungan elektro-penggumpalan dan pengelompokan dan penggumpalan dengan...
Published 2017“…Nilai optimum ketumpatan arus elektrik, jarak antara elektrod, pH awalan, masa tindak balas dan masa enapan masing-masing adalah 25 A/m2, 5 cm, 5, 75 min dan 40 min. Manakala, peratusan penyingkiran yang diperolehi bagi COD, SS, NH3-N, warna dan kekeruhan masing-masing adalah 90.03%, 94.46%, 62.03%, 95.68% dan 94.96%. …”
Get full text
Get full text
Get full text
Thesis -
642
Optimization of extraction process parameters for anti-cancer agent from Solanum Lycopersicum
Published 2011“…The design variables were the extraction time (min), extraction agitation speed (rpm) and solvent composition (%, v/v water/methanol). …”
Get full text
Book Chapter -
643
Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test
Published 1997“…A conventional four-ball wear testing machine with different loads was used at 1500 rev miny1 and a test duration of 1 min at ambient room temperature (approximately 28 8C). …”
Get full text
Article -
644
Design and simulation of a thermoelectric cooling system for motorcyclist helmet
Published 2012“…The numerical and experimental results showed a good agreement and indicated that the temperature inside the helmet was reduced from 25.5 °C to 19.3 °C in approximately 6 min.…”
Get full text
Get full text
Proceeding Paper -
645
Optimized neural network model for a potato storage system
Published 2013“…In comparison to a previous study, where the network was based on the min-max method of normalization, the network provided a better representation of the storage process. …”
Get full text
Article -
646
-
647
-
648
-
649
-
650
-
651
Investigation of machining parameters for the multiple response optimization of micro electrodischarge milling
Published 2009“…The optimized values of Ra, Ry, TWR, and MRR were 0.04, 0.34 μm, 0.044, and 0.08 mg min−1, respectively for 4.79 μm s−1 feed rate, 0.1 nF capacitance, and 80 V voltage. …”
Get full text
Article -
652
Application of activated carbon from empty fruit bunch (EFB) for mercury [Hg(II)] removal from aqueous solution
Published 2011“…It was found that the minimum residual concentration of mercury was 0.0075 mg/L (99.53%) at the condition of pH 6.5, agitation speed of 100 rpm, contact time of 70 min and AC dosage of 20 mg. This value was considered acceptable as it met the requirement of the Department of Environment, Malaysia.…”
Get full text
Article -
653
Statistical optimization of for chromium (IV) removal on aqueous solution using chitosan
Published 2011“…The experiment was described by varying chitosan dosage (10-30 mg), pH (5-8), contact time (10-90 min) and agitation speed (50-250 rpm). The initial chromium concentration was fixed to 20 mg/L. …”
Get full text
Article -
654
Straightforward synthesis of novel 1-(2'-α-O-D-glucopyranosyl ethyl) 2-arylbenzimidazoles
Published 2012“…The reduction and cyclocondensation steps for the aglycone synthesis proceeded efficiently under microwave irradiation to afford the appropriate benzimidazoles in excellent yields within 2-3 min. Glycosylation of the hydroxyethyl aglycones with the perbenzylated 1-hydroxy- glucopyranose, pretreated with the Appel-Lee reagent, followed by catalytic hydrogenolysis delivered the desired 1-(2'-α-O-D-glucopyranosyl ethyl) 2-aryl-benzimidazoles in a simple and straightforward manner.…”
Get full text
Article -
655
Cooling of motorcyclist helmet with thermoelectric module
Published 2013“…The numerical and experimental results showed a good agreement and indicated that the temperature inside the helmet was reduced from 25.5°C to 19.3°C in approximately 6 min.…”
Get full text
Article -
656
Thermal analysis of kenaf sandwich panel
Published 2013“…The temperature profile was from 27°C to 1000°C at a heating rate of 10°C/min. In this study, result shows that degradation of composites starts to occur at about 180°C. …”
Get full text
Article -
657
Isolation of individual hop iso-α-acids stereoisomers by β-cyclodextrin
Published 2010“…The separation from the mixture of stereoisomers was achieved by complexation, using ethanol:water (1:2, v/v) as a solvent at a temperature of 50 °C for 30 min. The molar ratio of iso-α-acids sample to β-cyclodextrin for complexation was 1:1. …”
Get full text
Article -
658
Empirical modelling of vibration in micro end milling of PMMA
Published 2013“…The optimum solution for minimum average vibrationis 64.3 Hz with spindle speed 2500 rpm, feed rate 2 mm/min and depth of cut 1.5 ìm. These micro end milling parameters are suitable to machine PMMA to get high precision. …”
Get full text
Article -
659
Autonomic nervous system mediates the hypotensive effects of aqueous and residual methanolic extracts of Syzygium polyanthum(Wight) Walp.var.polyanthum leaves in anaesthetized rats
Published 2013“…Blood pressure and heart were monitored for 20 min. AESP and met-AESP induced significant dose-dependent hypotension, but only 100 mg/kg AESP caused mild bradycardia (…”
Get full text
Article -
660
Tool wear during milling laminated carbon fibre reinforced plastic
Published 2015“…Cutting speed of 160–194 m/min and a feed rate of 0.14–0.225 mm/tooth on solid uncoated carbide during the milling process were discussed. …”
Get full text
Article