-
721
-
722
Intelligent diagnostic feedback for online multiple-choice questions
Published 2014Get full text
Article -
723
The association between trauma, offending behaviour, self harm and substance use with dissociation and absorption in male prisoners
Published 2008“…Much research has been conducted investigating the link between dissociation, fantasy proneness, and PTSD. …”
Get full text
Thesis -
724
Membrane vesicles of clostridioides difficile and other clostridial species
Published 2024Get full text
Book Section -
725
Effect of intrapartum pethidine on the neonatal outcome: is it duration related?
Published 2012“…All neonates delivered with good Apgar Score (AS), 8 at 1 minute and 9 at 5 minute except 1 with AS of 5 at 1 min and 7 at 5 min which delivered more than 4 hours after pethidine. …”
Get full text
Get full text
Article -
726
-
727
-
728
-
729
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatography for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
730
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatographyn for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
731
Deep Eutectic Solvent Coupled with High Performance Liquid Chromatography for Extraction of Bisphenols and Phthalates from Selected Freshwater Source in Selangor, Malaysia
Published 2023“…The optimum molar ratio of solvent and extraction time were 1:2 and 20 min, respectively. The best extraction temperature and volume of solvent with the highest recovery rate were 70 ºC and 3 mL. …”
Get full text
Article -
732
Amalan penyeliaan pensyarah pembimbing terhadap pelaksanaan latihan industri di Politeknik Sultan Haji Ahmad Shah Kuantan, Pahang
Published 2014“…Dapatan kajian menunjukkan skor min konstruk pengetahuan, kemahiran dan sikap merupakan aspek yang berada pada tahap yang sederhana dari pensyarah pembimbing dan pelajar. …”
Get full text
Get full text
Get full text
Thesis -
733
Ultrasonic and electroplating approach for washcoat of γ-alumina and nickel oxide (nio) catalyst on fecral substrate for catalytic converter
Published 2018“…Therefore, an appropriate techniques and parameter is UB+EL 30 min used for coating FeCrAl CATCO potential to improve physical properties and reduce emission.…”
Get full text
Get full text
Get full text
Thesis -
734
Sugarcane green ceramic hollow fibre membrane for oily wastewater separation
Published 2018“…The newly-developed ss-CHFM/WSBA induced excellent wettability properties with contact angle value of 161.1° at 60 min of grafting time, 3 cycle of grafting cycle and calcination temperature at 400 °C. …”
Get full text
Get full text
Get full text
Thesis -
735
Performance comparison of differential evolution and particle swarm optimization in constrained optimization
Published 2012“…This paper presents a comparative study for min-max constrained optimization using PSO and DE. …”
Get full text
Article -
736
Physical and mechanical properties of Thermoplastic Natural Rubber (TPNR) nanocomposites
Published 2012“…Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). …”
Get full text
Article -
737
Investigation of burr in high speed microdrilling
Published 2013“…The desirability of getting the minimum burr height is72% and the optimum parameters are 30000 rpm spindle speed and 0.2 mm/min feed rate.…”
Get full text
Article -
738
Tool life in high speed turning with negative rake angle
Published 2011“…The present work studies some aspects of turning process applied on mild steel using cermets tools at high speed cutting (1000mm/min) by using negative rake angle (90 to 12). The influence of increasing the cutting speed and negative rake angle on flank tool wear, cutting force, feeding forces and tool temperature were analyzed. …”
Get full text
Article -
739
-
740