-
401
Pembinaan dan penilaian program rekabentuk rasuk keluli (PRRK) sebagai alat kognitif dalam pembelajaran rekabentuk struktur di kalangan pelajar diploma kejuruteraan awam KUiTTHO
Published 2002“…Keputusan skor min menunjukkan isi PRKK adalah baik, bersifat mesra pengguna dan mempunyai sifat kebolehlaksanaan. …”
Get full text
Get full text
Get full text
Thesis -
402
Empirical analysis of rough set categorical clustering techniques based on rough purity and value set
Published 2017“…The recent techniques such as Information-Theoretic Dependency Roughness (ITDR), Maximum Dependency Attribute (MDA) and Maximum Significance Attribute (MSA) outperformed their predecessor approaches like Bi-Clustering (BC), Total Roughness (TR), Min-Min Roughness (MMR), and standard-deviation roughness (SDR). …”
Get full text
Get full text
Thesis -
403
Keberkesanan penggunaan edubase dalam kalangan pelajar teknikal yang berbeza gaya kognitif, afektif dan psikomotor di Politeknik Malaysia
Published 2017“…Namun, skor min menunjukkan kumpulan rawatan memberikan skor yang lebih cemerlang dan minat mereka juga turut meningkat dalam topik pembelajaran tersebut berbanding pelajar yang mengaplikasikan pembelajaran secara konvensional. …”
Get full text
Get full text
Get full text
Thesis -
404
Ultrasonic-Assisted Extraction (UAE) for enhanced recovery of bioactive phenolic compounds from cosmos caudatus leaves
Published 2021“…The effect of the extraction conditions was studied and optimised such as the solid-liquid ratio (10 to 30 g/ml), particle size (180 to 850 μm) and extraction time (20 to 30 min). Quercitrin and total phenolic content (TPC) were the selected response variables in this study. …”
Get full text
Article -
405
Tahap kompetensi pelajar kolej vokasional dalam melaksanakan kerja amali berpandukan domain psikomotor simpson
Published 2019“…Statistik deskriptif seperti min, sisihan piawai dan statistik inferensi seperti ujian-t, dan korelasi Spearman telah digunakan untuk menghurai dan menguji persoalan kajian. …”
Get full text
Get full text
Thesis -
406
Design and development of a small-scale 12S-14P outer rotor HEFSM
Published 2016“…Thus, the generated back EMF, torque, and power through simulation at a speed of 1,200 r/min is 6.58 V, 16.4 Nm, and 12.4 kW, correspondingly. …”
Get full text
Get full text
Get full text
Thesis -
407
Tapered microfluidic device for multi-particle separation based on sedimentation principle
Published 2017“…Successful multi-particle separations were observed using 20° and 25° tapered devices at 0.5 to 3.0 μl/min flow rates. These results were in agreement with simulation results obtained. …”
Get full text
Thesis -
408
Development of an electronic aerosol atomisation system for generating three-dimensional (3D) cells in microencapsulations and microtissues characterisation
Published 2016“…At an extrusion rate of 20 μl/min and airflow rate of 0.3 l/min, microcapsules with a diameter ranging from 220 - 270 μm were generated. …”
Get full text
Get full text
Thesis -
409
Persepsi terhadap system pembelajaran elektronik dalam kalangan pelajar Kolej Poly-Tech Mara Batu Pahat
Published 2017“…Dapatan kajian mendapati bahawa tahap pengetahuan pelajar terhadap sistem pembelajaran elektronik berada ditahap yang sederhana dengan nilai skor min 2.73. Manakala tahap penggunaan pelajara terhadap sistem pembelajaran elektronik adalah ditahap sederhana dimana nilai skor min 2.97. …”
Get full text
Get full text
Thesis -
410
-
411
Novel opto-electronic and plastic fibre sensors
Published 1998“…The middle POF is coupled to a red LED and emits light onto a flat target with the two outer fibres receiving the reflected light from the target and guiding it to two silicon PIN photodiodes. Theoretical investigations on the behaviour of the sensor are presented for ranges between 0 mm and 100 mm, and for targets with different reflectivities. …”
Get full text
Thesis -
412
-
413
Characterization and solvent stability of strep-tagged purified recombinant lipase from thermostable and solvent tolerant Bacillus sp. strain 42.
Published 2009“…Based on solvent stability studies in 30 min pre-incubation in 25% v/v solvents with a shaking rate at 150 strokes per min, the purified Lip 42 showed a different residual activity profiles depending on solvents and temperatures. …”
Get full text
Article -
414
Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
Published 2013“…Machining was performed at four different cutting speeds; 292, 388, 518 and 689 m/min using two different cutting parameters (feed rate, f = 0.2 mm/rev, depth of cut, d = 0.1 mm and f = 0.4 mm/rev, d = 0.2 mm). …”
Get full text
Article -
415
Bladder scan vs urethral cathetarization for measurement of immediate post partum bladder volume
Published 2011“…The mean for time interval between bladder scan and catheterization was 3 min(range between 1-8 min). There is a linear relationship between the bladder scan-estimated and catheter bladder volumes (r2=082). …”
Get full text
Get full text
Get full text
Proceeding Paper -
416
Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
Published 2013“…The highest MRR of 9.93mg/min was obtained with the current of 6.5A and pulse duration of 7.5 μs. …”
Get full text
Get full text
Get full text
Proceeding Paper -
417
Extraction and characterization of gelatin from camel skin (potential halal gelatin) and production of gelatin nanoparticles
Published 2020“…Central composite design combined with response surface methodology was used to achieve high gelatin yields under different extraction conditions: temperatures of 40, 60, and 80 °C; pH values of 1, 4, and 7; and extraction times of 0.5, 2.0, and 3.5 min. Maximum gelatin yield from camel skin (29.1%) was achieved at 71.87 °C and pH 5.26 after 2.58 min. …”
Get full text
Get full text
Article -
418
-
419
-
420