-
321
Do the innovative technological advancements foster the green transition pathways for Industry 5.0? A perspective towards carbon neutrality
Published 2025“…The transition to Industry 5.0 (I5.0) marks a pivotal moment in the industrial revolution, which aims to reconcile productivity with environmental responsibility. …”
Get full text
Article -
322
The evaluation of information security of hospital information system (his) using cobit 5 framework: case study at Soreang Hospital, Indonesia
Published 2019Subjects: “…T58.5-58.64 Information technology…”
Get full text
Get full text
Get full text
Thesis -
323
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…The cyclic plasticity presences following reciprocating sliding wear test of Ti-6Al-4V are examined using SEM. The black spot presence at the end of wear track are identified as an accumulation of ploughing that occurred during the sliding and proved by the highest hardness value recorded, 962 HV for contact pin Ø6.5 mm that determined by using Micro Vickers Hardness Tester. …”
Get full text
Get full text
Get full text
Thesis -
324
-
325
-
326
Parameter analysis of copper-nickel-tungsten prepared via powder metallurgy process for electrical discharge machining of polycrystalline diamond
Published 2019“…Factor B in which Composition of W; 5 Wt.%, 15 Wt. % and 25 Wt.%, was defined as numerical factor. …”
Get full text
Get full text
Get full text
Thesis -
327
Antiproliferative activity of five garcinia species collected in Sabah, Malaysian Borneo against estrogen receptor-human breast carcinoma (MCF-7) cell line
Published 2020“…The antiproliferative activity was assessed using 3-(4,5-dimethylthiazol-2-yl)-2,5- diphenyltetrazolium bromide (MTT) assay. …”
Get full text
Conference or Workshop Item -
328
The Right to a Defence at the Discretion of Judges
Published 2005“…Anna Demeneva (Sutyajnik) considers the right to legal assistance under the Russian Criminal Procedure Code.…”
Get full text
Article -
329
A grounded theory of the balancing act South Asian mothers engage in to negotiate a healthy family lifestyle
Published 2014“…Semi-structured interviews were carried out with seven female participants who were mothers to young children aged 5-12 years of age. Results The grounded theory is underpinned by three categories that emerged out of analysis of the data; cultural identity, health beliefs and barriers. …”
Get full text
Thesis -
330
-
331
-
332
Surface alloying of Ti-6Al-4V using Cu-TaC composite electrode during electrical discharge machining
Published 2011“…The peak current range of 3.5-5.5A and pulse duration of 3.3 - 5.3μsec were the machining conditions used as variables, while other conditions remained constant. …”
Get full text
Proceeding Paper -
333
Parametric Optimization in EDM of Ti-6Al-4V using Copper Tungsten Electrode and Positive Polarity: a statistical approach
Published 2011“…The experiments are carried out on Ti6Al4V. Experiments were conducted by varying the peak current, pulse on time and pulse off time and the corresponding values of surface roughness (SR) were measured. …”
Get full text
Book Chapter -
334
Chatter suppression in end milling of Titanium alloy Ti6Al4V applying permanent magnet clamped adjacent to the workpiece
Published 2011“…In addition, Quintana et al. [5] specified that chatter can be obviously predicted from the loud noise and the poor surface integrity due to the chatter mark.The chatter phenomenon actually can be suppressed by some of methods. …”
Get full text
Book Chapter -
335
Modeling for surface roughness in end-milling of Titanium alloy Ti-6Al-4V using uncoated WC-Co inserts
Published 2011“…Among all titanium alloys, Ti-6Al-4V is most widely used, so it has been chosen as the workpiece material in this study. …”
Get full text
Book Chapter -
336
Optimization of surface roughness in high speed end milling of Titanium alloy Ti-6Al-4V under dry conditions
Published 2011“…Among the titanium alloys, Ti-6Al-4V being the most commonly used and it is the workhorse alloy of the titanium industry, accounting for over 45% of the total titanium production [2]. …”
Get full text
Book Chapter -
337
Cutting force and tool life models in end milling titanium alloy ti-4al-4v with thermally-assisted machining
Published 2012“…This paper presents an approach to establish mathematical models for cutting force and tool life in end milling of titanium alloy Ti–6Al–4V using PCD inserts under thermally-assisted machining using high frequency induction heating. …”
Get full text
Article -
338
Surface roughness models for end milling titanium alloy TI-6AL-4V under room temperature and preheated machining
Published 2009“…This paper presents an approach in developing the first and second-order surface roughness models at 95% confidence level for end milling of titanium alloy Ti-6AI-4V using PCD inserts. The surface roughness models developed were for room temperature machining and preheated experiments. …”
Get full text
Proceeding Paper -
339
Surface roughness and surface integrity of end milled titanium alloy TI-6AL-4V at room temperature and preheated machining
Published 2009“…This paper is concerned with the surface roughness and surface integrity of titanium alloy Ti- 6AI-4V after end milling under room temperature and preheated conditions. …”
Get full text
Proceeding Paper -
340