-
101
-
102
-
103
-
104
-
105
Novel opto-electronic and plastic fibre sensors
Published 1998“…Matt white paper is concluded as the preferred type of target since it offers a longer linear operational range with less stringent alignment requirements as opposed to reflective targets. …”
Get full text
Thesis -
106
-
107
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…Simulated and measured results of the reflection coefficient, radiation pattern, gain, and efficiency show that the antenna design is in favorable agreement. Since the proposed antenna achieved wideband (1.91–6.75 GHz) using PIN diode configuration, using this technique the need for numerous electronic components to provide multiband frequency is avoided.…”
Get full text
Get full text
Article -
108
Road crashes among food delivery riders (P-Hailing) during pandemic in Kuala Lumpur
Published 2022“…Road accidents are a severe concem since they :result in death or injury. yet the number of fatalities among riders continue to rise. …”
Get full text
Conference or Workshop Item -
109
Road crashes among food delivery riders (P-Hailing) during pandemic in Kuala Lumpur
Published 2022“…Road accidents are a severe concem since they :result in death or injury. yet the number of fatalities among riders continue to rise. …”
Get full text
Conference or Workshop Item -
110
Road crashes among food delivery riders (p-hailing) during pandemic in Kuala Lumpur
Published 2022“…Road accidents are a severe concem since they :result in death or injury. yet the number of fatalities among riders continue to rise. …”
Get full text
Conference or Workshop Item -
111
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
112
Road Crashes Among Food Delivery Riders (P-Hailing) During Pandemic in Kuala Lumpur
Published 2024“…Road accidents are a severe concem since they :result in death or injury. yet the number of fatalities among riders continue to rise. …”
Get full text
Conference or Workshop Item -
113
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
114
Antivirals for broader coverage against human coronaviruses
Published 2024“…Spike is also not applicable for targeting other HCoVs as these are not well-conserved sequences among human CoVs. …”
Get full text
Article -
115
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
116
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
117
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
118
Transmission service charge methodology for pool power market
Published 2009“…It is hard to identify the power contribution of each user in a line since the power output from different power plants are "pooled" together to meet the load demand. …”
Get full text
Thesis -
119
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
120
Utilizing rapid prototyping 3D printer for fabricating flexographic PDMS printing plate
Published 2016“…However, the micro-scale multiple solid line array of 100micron and 25micron successfully made by nikel platting and glass etching master mould respectively. …”
Get full text
Article