-
661
-
662
Model fitting for biodiesel yield analysis from crude palm oil (CPO)
Published 2010“…This was carried by finding the optimal values of reaction time, 60 min, reaction temperature, 60 ºC, agitation speed, 250 rpm, molar ratio of methanol-to-oil, 10:1 (m/m), and dosage of the catalyst, 1.4 (%wt). …”
Get full text
Proceeding Paper -
663
Palm tocotrienol-rich fraction reduced plasma homocysteine and heart oxidative stress in rats fed with a high-methionine diet
Published 2013“…The high-methionine group had a lower glutathione peroxidase activity (49 ± 3 vs 69 ± 4 pmol/mg protein/min) than the control group. This reduction was reversed by palm TRF at 60 and 150 mg/kg diet (p < 0.05), but not by folate. …”
Get full text
Article -
664
Purification, characterization and kinetic properties of alpha-naphthyl acetate esterase from wheat flour (Triticum aestivum)
Published 2018“…Using a 16 mM solution of alpha naphthyl acetate as substrate, the maximum activity of the purified enzyme, alpha naphthyl acetate esterase (ANAE) was found to be 0.78 U at the optimum conditions of 40 ◦C and pH 8.0 for 15 min of incubation. The Michaelis–Menten parameters Km and Vmax of the purified enzyme were estimated using Langmuir linear plot as 22.5 mM and 4.71 U mg−1, respectively. …”
Get full text
Article -
665
Optimization of supercritical carbon dioxide extraction parameters of cocoa butter analogy fat from mango seed kernel oil using response surface methodology
Published 2015“…The optimized oil yield was predicted to be 11.29 % at 44.2 MPa, 72.2 °C and CO2 flow rate of 3.4 ml/min which was close to the oil yield (11.7 %) of Soxhlet extraction method. …”
Get full text
Article -
666
A comparative study of dexmedetomidine and propofol for sedation in the cardiothoracic intensive care unit
Published 2007“…Results: Patients sedated with dexmedetomidine required significantly lower dose of morphine compared to propofol [mean (sd): 12.80 (2.61) versus 15.86 (1.87) mg/kg/min, p=0.00]. Mean heart rate was also significantly lower in dexmedetomidine group compared to propofol group [mean (CI): 74.48 (70.38,78.59) versus 83.85 (79.61,88.09) per minutes, p=0.00]. …”
Get full text
Article -
667
Stability testing of oil-in-water emulsion of Syzygium aromaticum (clove)
Published 2015“…Initial screening was done on the prepared formulations with centrifugation (3000 rpm, 3 min) to detect for any phase separation in these formulations. …”
Get full text
Article -
668
Effects of water-bath stunning on the death of poultry and myofiber apoptosis
Published 2014“…Meat samples from stunned and unstunned chickens were preserved in formalin within 30 min postmortem and apoptotic activity of the muscles were analysed using TUNEL assay and immunohistochemistry. …”
Get full text
Proceeding Paper -
669
Turbidity and suspended solids removal from highstrength wastewater using high surface area adsorbent: mechanistic pathway and statistical analysis
Published 2016“…Adsorption efficiency of 89.1 and 91.4% were observed for suspended solids and turbidity, respectively, at the operating condition of 3.5 g PAC dosage, 45 min contact time and 150 rpm mixing speed. The analysis of variance also revealed that the actual and model predicted values were in agreement with R2 values of 0.9949 and 0.9991for suspended solids and turbidity, respectively. …”
Get full text
Get full text
Get full text
Article -
670
Development of biological process with pure bacterial cultures for effective bioconversion of sewage treatment plant sludge
Published 2007“…The strain S-1 (IWK1001) showed lower TSS content (0.8% TSS), maximumCODremoval (84%) and increased filterability (1.1 min/10 mL of filtrate) of treated sludge followed by the strains S-11, S-14, S-2, S-15, S-13, S-7, S-8, S-4, S-3, S-6, S-12,S-16, S-17 and S-9. …”
Get full text
Article -
671
Study on micro-patterning process of vertically aligned carbon nanotubes (VACNTs)
Published 2016“…A minimum average surface roughness of Ra D 15 nm was achieved with 2000 rpm spindle speed, 1 mm/min bending speed and 1 mm step size.…”
Get full text
Get full text
Get full text
Article -
672
Production of biodiesel from sludge palm oil by esterification using P-toluenesulfonic acid
Published 2009“…Batch esterification process of SPO was carried out to study the influence of PTSA dosage (0.25-10% wt/wt), molar ratio of methanol to SPO (6:1-20:1), temperature (40-80oC), reaction time (30-120 min). The effects of those parameters on FFA content, yield of treated SPO and conversion of FFA to FAME were monitored. …”
Get full text
Proceeding Paper -
673
Heavy metals removal from synthetic wastewater by a novel nano-size composite adsorbent
Published 2011“…Experimental conditions resulting in optimal metals adsorption were observed at pH 5, 1 g/L dosage and 60 min contact time. It was noted that the percentage of metals removal at the equilibrium condition varied for each metal, with lead recording 99 %, copper 61 % and nickel 20 % , giving metal affinity trend of Pb2+ > Cu2+ > Ni2+ on the adsorbent. …”
Get full text
Article -
674
Biodiesel production from waste cooking oil using calcium oxide/nanocrystal cellulose/polyvinyl alcohol catalyst in a packed bed reactor
Published 2020“…Investigation on the kinetic of the reaction specified that the reaction followed pseudo first order reaction with k-value ranged from 0.0092 min−1 to 0.0151 cm−1 and Thiele modulus was less than 2. …”
Get full text
Get full text
Article -
675
An investigation of hole quality during drilling of carbon fibre reinforced plastic and titanium (Ti6Al4V) using tungsten carbide drills
Published 2020“…The drilling trials were conducted through CFRP/Ti stacks, CFRP-only and Ti-only using carbide drills (6.1 mm diameter) at a cutting speed of 50 m/min and a feed rate of 0.05 mm/rev. The quality of the drilled holes was evaluated with respect to the hole diameters, delamination and pull-out of CFRP as well as Ti burr. …”
Get full text
Get full text
Proceeding Paper -
676
-
677
-
678
-
679
-
680