Showing 541 - 560 results of 948 for search '(((pina OR (rice OR ssfine)) OR (pine OR ssfine)) OR (sspingl OR (pin OR min)))', query time: 0.07s Refine Results
  1. 541

    Performance comparison of differential evolution and particle swarm optimization in constrained optimization by Iwan, Mahmud, Akmeliawati, Rini, Faisal, Tarig, Al-Assadi, Hayder M.A.A.

    Published 2012
    “…This paper presents a comparative study for min-max constrained optimization using PSO and DE. …”
    Get full text
    Article
  2. 542

    Physical and mechanical properties of Thermoplastic Natural Rubber (TPNR) nanocomposites by Hassan, Noor Azlina, Hassan, Norita, Ahmad, Sahrim, Rasid, Rozaidi, Anuar, Hazleen, Bonnia, Noor Najmi, Surip, Siti Norasmah

    Published 2012
    “…Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). …”
    Get full text
    Article
  3. 543

    Investigation of burr in high speed microdrilling by Ali, Mohammad Yeakub, Mohamed, Abd. Rahman, Fadila, N., Hannah, N.

    Published 2013
    “…The desirability of getting the minimum burr height is72% and the optimum parameters are 30000 rpm spindle speed and 0.2 mm/min feed rate.…”
    Get full text
    Article
  4. 544

    Tool life in high speed turning with negative rake angle by Adesta, Erry Yulian Triblas, Al Hazza, Muataz Hazza Faizi

    Published 2011
    “…The present work studies some aspects of turning process applied on mild steel using cermets tools at high speed cutting (1000mm/min) by using negative rake angle (90 to 12). The influence of increasing the cutting speed and negative rake angle on flank tool wear, cutting force, feeding forces and tool temperature were analyzed. …”
    Get full text
    Article
  5. 545
  6. 546
  7. 547
  8. 548

    Effect of intrapartum pethidine on the neonatal outcome: is it duration related? by Abdulwahab, Dalia F, Husien, Roziah, Busurerah, Ruqaiah, Awang, Mokhtar, Ismail, Rozihan

    Published 2012
    “…All neonates delivered with good Apgar Score (AS), 8 at 1 minute and 9 at 5 minute except 1 with AS of 5 at 1 min and 7 at 5 min which delivered more than 4 hours after pethidine. …”
    Get full text
    Get full text
    Get full text
    Proceeding Paper
  9. 549
  10. 550
  11. 551
  12. 552

    Olahan air sisa pusat penyembelihan ayam menggunakan elektrod keluli tahan karat dan aluminum melalui proses gabungan elektro-penggumpalan dan pengelompokan dan penggumpalan dengan... by Sakury, Khairudin

    Published 2017
    “…Nilai optimum ketumpatan arus elektrik, jarak antara elektrod, pH awalan, masa tindak balas dan masa enapan masing-masing adalah 25 A/m2, 5 cm, 5, 75 min dan 40 min. Manakala, peratusan penyingkiran yang diperolehi bagi COD, SS, NH3-N, warna dan kekeruhan masing-masing adalah 90.03%, 94.46%, 62.03%, 95.68% dan 94.96%. …”
    Get full text
    Get full text
    Get full text
    Thesis
  13. 553

    Optimization of extraction process parameters for anti-cancer agent from Solanum Lycopersicum by Amid, Azura, Ahmad, Abdul Aziz, Ahmad Raus, Raha

    Published 2011
    “…The design variables were the extraction time (min), extraction agitation speed (rpm) and solvent composition (%, v/v water/methanol). …”
    Get full text
    Book Chapter
  14. 554

    Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test by Maleque, Md. Abdul, Masjuki, H.H.

    Published 1997
    “…A conventional four-ball wear testing machine with different loads was used at 1500 rev miny1 and a test duration of 1 min at ambient room temperature (approximately 28 8C). …”
    Get full text
    Article
  15. 555

    Design and simulation of a thermoelectric cooling system for motorcyclist helmet by Hrairi, Meftah, Abdullah, Abdullah F., Ahmed, Mirghani Ishak

    Published 2012
    “…The numerical and experimental results showed a good agreement and indicated that the temperature inside the helmet was reduced from 25.5 °C to 19.3 °C in approximately 6 min.…”
    Get full text
    Get full text
    Proceeding Paper
  16. 556

    Optimized neural network model for a potato storage system by Abdulquadri Oluwo, Adeyinka, Khan, Md. Raisuddin, Salami, Momoh Jimoh Emiyoka

    Published 2013
    “…In comparison to a previous study, where the network was based on the min-max method of normalization, the network provided a better representation of the storage process. …”
    Get full text
    Article
  17. 557
  18. 558
  19. 559
  20. 560