The effect of incorporating lithium fluoride on the compressive strength and diametric tensile strength of glass ionomer cement by Mustafa, Ammar A., Al-Khateeb, Khalid A. Saeed, Ismail, Ahmad Faris

“…The specimens were tested in a Universal Testing Machine (Instron 1122, Instron corp., High Wycombe, U.K.) at a crosshead speed of 1.0mm/min for CS and 0.5mm/min for the DTS test until failure occurred. …”
Get full text
Get full text

Adsorption of copper, nickel and lead ions from synthetic semiconductor industrial wastewater by palm shell activated carbon by Onundi, Yusuf Bamidele, Al-Mamun, Abdullah, Al-Khatib, Ma'an Fahmi Rashid, Ahmed, Yehya M.

“…The percentage metal removal approached equilibrium within 30 min for lead, 75 min for copper and nickel, with lead recording 100 %, copper 97 % and nickel 55 % removal, having a trend of Pb2+ > Cu2+ > Ni2+ . …”
Get full text

Assessment of heavy metals in Malacca river water using electrokinetic technique by Mohamad, Nur Farahin, Abdullah, Shakila, Embong, Zaidi

“…The optimal removal was observed at a voltage of 90 V, with an electrode distance of 10cm and operational time of 30 min. The pH water was acidic which below than 7 after the electrokinetic process. …”
Get full text

Penghasilan manual rjngkas penggunaan alat Total Station Sokkia Set5f dan Perisian Sdr Mapping & Design untuk automasi ukur topografi by Bagu, Pitus @ Vitus

“…Analisis data dilakukan menggunakan perisian SPSS versi 11.0. Hasil analisis skor min menunjukkan kesemua responden bersetuju bahawa manual dalam bentuk buku ini menarik Min ( M ) ^ ^ dan Sisihan Piawai (SD) = .535 tetapi kurang interaktif (M) = 2.29 dan (SD) = 0.488. …”
Get full text
Get full text
Get full text

Preparation and surface modification of activated carbon from coconut shells for benzene and toluene adsorption from water by Mohammed, Jibril

Get full text

Treatment system for soy sauce wastewater through granular sequencing batch reactor by Harun, Hasnida

Get full text

Influence of cutting parameters on chatter and tool wear during end milling of stainless steel conducted on VMC by Amin, A. K. M. Nurul, Imran, M., Arif, M.

“…The performance of the tool is evaluated from the point of view of its wear intensity, mechanism of failure and generation and effect of chatter on tool wear and vice versa. The investigations were aimed at determining the effect of cutting parameters, specifically cutting speed, feed and depth of cut, on chatter amplitude, tool wear rate, mechanism of tool wear and using these data and machined surface roughness values from previous work to come up with recommended values of cutting parameters for semi-finish and finish end milling operation of stainless steel work materials. …”
Get full text

Substrate placement inside CVD tube for graphene production by Osman, Muhammad Naqib, Ani, Mohd Hanafi, Syed Abu Bakar, Syed Noh

“…For flow with higher flowrate, it requires longer distance for the flow to become smooth and laminar and vice versa.…”
Get full text
Get full text

Water filtration performance comparison of sayong ball clay membrane produced by gel casting and spark plasma sintering methods by Mohd. Zaidan, Nurhanna

Get full text

The influence of cation exchange capacity towards electrical resistivity value for fine grained soil by Azmi, Mohammad Izzat Shaffiq

“…The CEC of a mineral mixture increased when a high percentage of minerals with high CEC were added and vice versa, for example the mixture of montmorillonite and illite were 29.82 meq/100g and the mixture of kaoline and quartz were 4.34 meq/100g. …”
Get full text
Get full text
Get full text

Investigation of dual-pump fiber optical parametric amplifier using highly nonlinear dispersion shifted fiber by Abdullahi, Abdirahman Mohamud

“…It shows when parametric gain increases, the saturation power reduces and vice versa.…”
Get full text
Get full text
Get full text

Optimization of supercritical carbon dioxide extraction of bioactive flavonoid compounds from spearmint (Mentha Spicata l.) leaves by using response surface methodology by Bimakr, Mandana, Abdul Rahman, Russly, Ganjloo, Ali, Taip, Farah Saleena, Md Salleh, Liza, Sarker, Md. Zaidul Islam

“…The optimal conditions were identified as 209.39 bar pressure, 50.00 °C temperature and 7.39 g/min co-solvent amount. The obtained extract under optimum SC-CO2 condition was analysed by high-performance liquid chromatography. …”
Get full text
Get full text

Optimization of ultrasound-assisted extraction of crude oil from winter melon (Benincasa hispida) seed using response surface methodology and evaluation of its antioxidant activity... by Bimakr, Mandana, Abdul Rahman, Russly, Taip, Farah Saleena, Mohd Adzahan, Noranizan, Sarker, Md. Zaidul Islam, Ganjloo, Ali

“…Optimal conditions were identified as 65% power level, 52 °C temperature and 36 min sonication time for maximum crude yield (108.62 mg-extract/g-dried matter). …”
Get full text

Photocatalytic decomposition of acetaldehyde gas on TiO2-SiO2 thin film photocatalyst ― a kinetic analysis by Abdul Aziz , Radhiyah, Sopyan, Iis

“…It is found that the first order reaction rate constant (k) of the TF95/5 thin film photocatalyst (1.2438 µmol dm-3 min-1) is higher than that of TF90/10 thin film (0.3648 µmol dm-3 min-1). …”
Get full text

Supercritical carbon dioxide extraction of oil from Thunnus tonggol head by optimization of process parameters using response surface methodology by Ferdosh, Sahena, Sarker, Md. Zaidul Islam, Rahman, Nik Norulaini Nik Ab, Akand, Md Jahurul Haque, Ghafoor, Kashif, Awang, Mohamed Bin, Kadir, Mohd Omar Ab

“…Total oil was extracted from ground fish head of Longtail tuna (Thunnus tonggol) using supercritical carbon dioxide (SC-CO2) at 20 to 40 MPa, 45 to 65 oC and 1 to 3 ml min−1. Response surface methodology (RSM) was employed to optimize the operating conditions of the SC-CO2 technique where the highest oil yield was obtained (35.6% on dry weight basis) at 40 MPa, 65 oC, and 3 ml min−1. …”
Get full text

Dry machining of brass using titanium carbonitride (TiCN) coated tool by Mohamed Ariff, Tasnim Firdaus, Kamarudin, Mohd Syahidan, Haron, Mohd Amiruddin

“…The optimum cutting condition for wet and dry machining of brass using TiCN coated cutting tool was found to be 498 m/min at d = 0.2 mm, f = 0.4 mm/rev. The tool tip temperature obtained from dry machining did not influence tool wear since the temperature rise is quite similar to the wet machining temperatures. …”
Get full text

Bladder scan vs urethral catheterization for measurement of immediate post partum bladder volume by Ibrahim, Norliza, Nusee, Zalina, Mohd Rus, Razman, Abdullah, Suhaiza, Ismail, Hamizah, Abdulwahab, Dalia F, Awang, Mokhtar

“…The mean for time interval between bladder scan and catheterization was 3 min(range between 1-8 min). There is a linear relationship between the bladder scan-estimated and catheter bladder volumes (r2=082). …”
Get full text

Rapid and sensitive LC method for the analysis of Gemifloxacin in Human plasma by Chakrabarty, Uday Sankar, Das, Ayan, Bhaumik, Uttam, Chatterjee, Bappaditya, Nandi, Utpal, Pal, Tapan Kumar

“…The mixture was then sonicated for 10 min followed by 20 min centrifugation at 5000 rpm (g = 3600). …”
Get full text

Personal control related to childbirth satisfaction among postpartum mothers in Hospital Tengku Ampuan Afzan (HTAA) by Mohd Arifin, Siti Roshaidai, Addenan, Nor Ashikin

“…Findings: The mean score for personal control among postnatal mother was 52.56 [SD = 10.693, min max (29, 70)] with the mean childbirth satisfaction score of 140.06 [SD = 17.109, min max (89, 170)]. …”
Get full text

Effect of peak current on material removal rate for electrical discharge machining of non-conductive Al2O3 ceramic by Moudood, M. A., Sabur, A., Ali, Mohammad Yeakub, Jaafar, Israd Hakim

“…MRR was found to be 0.052 mm3/min at peak current 1.1 A and it was found to be 0.132 mm3/min at peak current 1.3 A.…”
Get full text
Get full text