-
121
-
122
A review on equipment protection and system protection relay in power system
Published 2017Get full text
Article -
123
Reliable power system operation plan: steady state contingency analysis
Published 2017Get full text
Article -
124
-
125
-
126
-
127
-
128
-
129
-
130
Dynamic duty cycle mechnism for mobility in wirless sensor networks
Published 2020“…Done through two diverse scenarios that are the sink and the sensor nodes fixed, and the sink nodes and the nodes are the mobility that occurs. …”
Get full text
Get full text
Get full text
Thesis -
131
Joint routing protocol and image compression algorithm for prolonging node lifetime in wireless sensor network
Published 2018“…The conventional data routing protocols do not consider the power available at the node on the path from source to sink, thus they result in the exhaustion and eventual death of nodes surrounding the sink node, thus generating routing holes reducing the network throughput. …”
Get full text
Get full text
Get full text
Thesis -
132
MHD stagnation flow of nanofluid past a permeable shrinking surface with various conditions
Published 2018“…The purpose of the present study is to analyze the effects of slip and heat source/sink on magnetohydrodynamic stagnation-point flow and heat transfer past a permeable shrinking surface with convective boundary condition. …”
Get full text
Get full text
Get full text
Thesis -
133
Preparation of injection moulding processing for high density polyethylene via moldflow advisor 2015 simulation
Published 2018“…Both simulation and practical results have no sink marks. Therefore, it can be concluded that the simulation process had provided a good prediction for practical injection moulding preparation. …”
Article -
134
Radiative MHD Boundary Layer Flow and Heat Transfer Characteristics of Fe-Casson Base Nanofluid over Stretching/Shrinking Surface
Published 2024“…This paper considers the MHD boundary layer flow and heat transfer characteristics of FeCasson-based nanofluid over an exponentially stretching/shrinking surface, including heat source/sink and Newtonian heating effects. In this regard, to develop the system of the governing equations, the one phase model named as Tiwari and Das model is considered with iron nanoparticles. …”
Get full text
Article -
135
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
136
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
137
Performance of various forecasting algorithms to reduce the number of transmitted packets by sensor node in wireless sensor networks
Published 2018“…Additionally, in terms of absolute error in the data at the sink, the EDCD1 algorithm shows the best performance with less average error at 2.2803 for all sensors compared to others algorithms.…”
Get full text
Get full text
Get full text
Thesis -
138
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
139
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
140
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis