Tolerance towards sensor failures: an application to a double inverted pendulum by Ng, Kok Yew, Tan, Chee Pin, Akmeliawati, Rini

Get full text

Roll and yaw stabilisation using nonlinear energy method by Lim, Jen Nee Jones, Akmeliawati, Rini, Chee, Pin Tan

Get full text

Automatic aircraft landing control using nonlinear energy method by Jones, Lim Jen Nee, Akmeliawati, Rini, Tan, Chee Pin

Get full text
Get full text

Disturbance decoupled fault reconstruction using sliding mode observers by Kok, Yew Ng, Chee, Pin Tan, Akmeliawati, Rini, Edwards, Christopher

Get full text

New results in disturbance decoupled fault reconstruction in linear uncertain systems using two sliding mode observers in cascade by Ng, Kok Yew, Tan, Chee Pin, Man, Zhihong, Akmeliawati, Rini

Get full text

Disturbance decoupled fault reconstruction using sliding mode observers by Kok, Yew Ng, Chee, Pin Tan, Akmeliawati, Rini, Edwards, Christopher

Get full text

Preliminary design of sliding mode controller for angular positional tracking of an aircraft by Jones, Lim Jen Nee, Tan, Chee Pin, Man, zhihong, Akmeliawati, Rini

Get full text

Spray angle and droplet size analysis for gas turbine fogging by Tan, Beng Chiat

Get full text

Shear strength analysis of concrete beams reinforced with GFRP bars using strut and tie model by Mokhtar, Norfaniza

“…The experimental approved that the spacing between shear cracks for the specimens with larger shear span to depth ratio is greater than the smaller shear span to depth ratio and while the shear span to depth ratio (a/d) decreases, the shear strength increase. …”
Get full text
Get full text
Get full text

Development of switchable planar reflectors for beam shaping realization by Abbasi, Muhammad Inam

“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text

Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test by Mohd Harun, Dalila

“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text

Electrical breakdown and structural characterization in synthetic resins using optical techniques by Dodd, Stephen John

“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text

Evaluation of classifiers in a pressure and latency-based typing biometric system by Moez Khan, Imran, ., Imama, Ushama, K. M., Aibinu, Abiodun Musa, Lai, Weng Kin

“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text

An investigation of defect formation and growth in epoxy resin using light scattering methods by Perkins, Elaine Ann

“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text

Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing by ISA, SITI RAHENA, JUSOH, MUZAMMIL, THENNARASAN SABAPATHY, THENNARASAN SABAPATHY, KAMARUDIN, MUHAMMAD RAMLEE, OSMAN, MOHAMED NASRUN, AKRAM ALOMAINY, AKRAM ALOMAINY

“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text

Evaluation of sustainable supply chain risk: evidence from the Iranian food industry by Tavakoli Haji Abadi, Yasamin, Avakh Darestani, Soroush

“…The final weight of the main and sub-criteria was obtained using the F-BWM method via LINGO software. Risk management in the sustainable supply chain has the role of identifying, analyzing and providing solutions to control risks. …”
Get full text

Analytical Finite Element Formulation of Non-uniform Euler-Bernoulli Beam by Sulaeman, Erwin, Kapania, Rakesh

“…To satisfy some requirements, it is not uncommon that the beam has to posses a non-uniform distribution of its cross section along the span. A common approach to analyze such a structure is by using a variational principle to develop the element stiffness matrix. …”
Get full text

Wear characteristics of Fe-C-Si and Fe-C-Al cast irons by Shaha, Sugrib Kumar, Haque, Md. Mohafizul, Khan, Ahsan Ali

“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text

Biomechanical evaluation and new improvement on ankle external fixator by Ramlee, Muhammad Hanif

Get full text

Methodology to develop bottleneck-based heuristic for permutation flow shop scheduling by Isa, Noor Amira, Ahmad Bareduan, Salleh

“…To date, the Nawaz-Enscore-Ham (NEH) algorithm is still recognized as the best heuristic in solving make span problem in scheduling environment. A very detail step by step methodology to develop the BNB heuristic was thoroughly discussed and elaborated in this paper. …”
Get full text