-
221
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
222
Back pain and osteolysis of the thoracic spine in an adult: a case of monostotic fibrous dysplasia masquerading as spinal metastasis
Published 2013“…Posterior element of T12 and bilateral erector spinae muscles sent for histopathological evaluation. …”
Get full text
Get full text
Proceeding Paper -
223
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
224
Material properties and design aspects of folding bicycle frame
Published 2011“…The relationship between materials properties and design is not straight forward because the behavior of the material in the finished product could be different from that of the raw material. The swing hinge technique could be a better technique in the design for the folding bicycle frame.…”
Get full text
Article -
225
-
226
-
227
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
228
PCR-based chromosome walking: the SFR 3 case
Published 2006“…Eleven new PCR markers had been designed to fine map the gene. Roughly 557 F2 plants tested in these experiments and 38 lines were then used in the fine mapping experiments. …”
Get full text
Article -
229
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
230
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
231
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
232
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
233
-
234
Risk of Escherichia coli O157:H7 transmission linked to the consumption of raw milk
Published 2013Get full text
Article -
235
Biotar ironmaking using wooden biomass and nanoporous iron ore
Published 2009“…In our experiments, three types of iron ores containing different amounts of combined water (CW; 1.6, 3.8, and 9.0 mass %) were first dehydrated at 450 °C to make them porous and then heated with pine tree biomass at 500-600 °C for the gasification and the tar vapor generated was decomposed to deposit carbon within/on the porous ores. …”
Get full text
Article -
236
Physico-mechanical properties of polymer concrete containing micro-filler of palm oil fuel ash
Published 2018“…Objective of this study is to present a research conducted on ground (fine) and unground (coarse) POFA in polymer concrete (PC) followed by determination on the physico-mechanical properties of PC. …”
Article -
237
Bitumen modification using oil palm fruit ash for stone mastic asphalt
Published 2024Get full text
Thesis -
238
Influence of mesh sizes and orientations on expanded aluminium sheets on tensile performances
Published 2022“…According to the results of the experiment, specimens with fine mesh have higher tensile stress, which is 44.90 MPa for fine mesh specimens with a 30° orientation, compared to medium and coarse mesh sizes, which have the lowest strength, which is 7.06 MPa for coarse mesh specimens with a 60° orientation. …”
Get full text
Conference or Workshop Item -
239
The Exploration of the Characteristics of Concrete Incorporating Ultrafine Coal Bottom Ash and Spent Garnet
Published 2024“…Two such materials, ultrafine coal bottom ash (uCBA) and spent garnet (SG), have shown potential as substitutes for cement and fine aggregate, respectively. This research examines the effectiveness of uCBA as a partial replacement for cement and SG as a partial replacement for fine aggregate in concrete, at varying levels of 3%, 6%, and 9% for uCBA and 10%, 20%, and 30% for SG. …”
Get full text
Article -
240
The Exploration of the Characteristics of Concrete Incorporating Ultrafine Coal Bottom Ash and Spent Garnet
Published 2024“…Two such materials, ultrafine coal bottom ash (uCBA) and spent garnet (SG), have shown potential as substitutes for cement and fine aggregate, respectively. This research examines the effectiveness of uCBA as a partial replacement for cement and SG as a partial replacement for fine aggregate in concrete, at varying levels of 3%, 6%, and 9% for uCBA and 10%, 20%, and 30% for SG. …”
Get full text
Article