-
301
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
302
-
303
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
304
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
305
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
306
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
307
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
308
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
309
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
310
Material properties and design aspects of folding bicycle frame
Published 2011“…The relationship between materials properties and design is not straight forward because the behavior of the material in the finished product could be different from that of the raw material. The swing hinge technique could be a better technique in the design for the folding bicycle frame.…”
Get full text
Article -
311
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
312
PCR-based chromosome walking: the SFR 3 case
Published 2006“…Eleven new PCR markers had been designed to fine map the gene. Roughly 557 F2 plants tested in these experiments and 38 lines were then used in the fine mapping experiments. …”
Get full text
Article -
313
Biomedical Analysis of Lateral Lumbar Interbody Fusion (LLIF) Cage for Lumbar Vertebrae
Published 2023“…Objective: To develop the interbody cages implanted between the lumbar vertebrae by evaluating the strength of the bone model and the spinal cage. Materials and methods: In this study, finite element analysis (FEA) was applied using Mechanical Finder software (MF) to develop a 3D spine model lumbar vertebrae of the fourth and fifth lumbar vertebrae (L4 - L5) with various interbody cage designs, including honeycomb and rectilinear patterns with 50%, 70%, and 100% infill densities. …”
Get full text
Article -
314
Analysis re-entrant honeycomb auxetic structure for Lumbar vertebrae using finite element analysis
Published 2024“…Lumbar spinal fusion is a frequent surgical solution among people who are experiencing severe persistent lower back pain. …”
Get full text
Article -
315
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
316
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
317
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
318
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
319
Spores that crush the spine in infancy: a diagnostic dilemma for an infant with special tuberculosis
“…The case highlights the dilemma with the diagnosis we encountered until establish the final diagnosis which is spinal tuberculosis. We highlighted a lot of important lessons.…”
Get full text
Get full text
Copyright -
320