-
161
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
162
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
163
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
164
-
165
-
166
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
167
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
168
-
169
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
170
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
171
Investigation of aerodynamic parameters of a hybrid airship
Published 2012“…The aerodynamic parameters of a preliminary winged-hull airship design are investigated. The research methodology involved the use of numerical simulation and wind tunnel testing. …”
Get full text
Article -
172
-
173
-
174
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
175
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
176
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
177
Influence of differential spoiler settings on the wake the vortex characterization and alleviation
Published 2010“…Experimental investigations using particle image velocimetry technique have been carried out for the evaluation of the differential spoiler setting capabilities in modifying the spanwise wing load and further reduce the wake vortex hazard. …”
Get full text
Article -
178
Influence of differential spoiler settings on the wake vortex characterization and alleviation
Published 2010“…Experimental investigations using particle image velocimetry technique have been carried out for the evaluation of the differential spoiler setting capabilities in modifying the spanwise wing load and further reduce the wake vortex hazard. …”
Get full text
Article -
179
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
180
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article