-
581
A business model architecture framework (BMAF) for the architecting of business to business electronic commerce
Published 2014“…The result is a mix of concepts with the same meanings but different names and vice versa. Also, traditional solutions have failed to successfully support the development of a business model for e-commerce as they do not provide full and complete support (at not enough level of detail), but only provide general guidelines or steps described in quite brief terms. …”
Get full text
Thesis -
582
The fabrication of TiO2 nanostructures on porous silicon for thermoelectric application
Published 2021“…Therefore, the needs for high-performance thermoelectric (TE) materials to convert heat into electricity and vice versa is become compelling. Nowadays, the leading TE materials are Bi2Te3-based alloys, PbTe, PbSe, SiGe, Mg2X (X = Si, Ge, Sn), skutterudite, and half-Heusler alloys. …”
Get full text
Get full text
Get full text
Thesis -
583
-
584
Study the performance of porous pavement on urban thermal environment. Part 1: Field observation
Published 2008“…A numerical method was developed to study the thermal characteristics of porous pavement under fine meteorological conditions, which will be discussed in our next effort. …”
Get full text
Proceeding Paper -
585
Structure and function of proteins important in Mycobacterium tuberculosis energy metabolism
Published 2009“…Purification of a GST-tagged construct to eliminate proteolytic degradation and further fine screening is ongoing to obtain better quality crystals for X-ray diffraction. …”
Get full text
Proceeding Paper -
586
Spatial distribution of lead and copper in the bottom sediments of Pahang River estuary, Pahang, Malaysia
Published 2010“…The concentration for both metals increased with the decrease of mean size, suggesting their association with the fine fraction of the sediments.…”
Get full text
Article -
587
Aluminium metal matrix composite: improving wear performance through treatment
Published 2011“…The triple particle size (TPS) composite consist of SiC of three different sizes viz., coarse, intermediate and fine. The solution heat treatment was carried out on cast specimens at 540 °C for four hours followed by precipitation treatment. …”
Get full text
Article -
588
Islamic architecture : its philosophy, spiritual significance & some early developments
Published 2009“…Islamic architecture is a fine blend of all these factors which are interwoven with the treads of the belief system, principles, teachings and values of Islam. …”
Get full text
Book -
589
Tendon bioreactor
Published 2016“…The parameters such as frequency, the duration and the strain applied can further fine tune to meet the design requirement. Nevertheless, the optimum function of the bioreactor also relies on the mass transport of the nutrients or the medium circulation. …”
Get full text
Monograph -
590
An SEM flashover: technique to characterize wide band gap insulators
Published 2006“…An SEM may be used not only to observe a surface image but also to provide a fine electron beam for charging an uncoated insulator surface at once. …”
Get full text
Proceeding Paper -
591
CPW-fed printed UWB antenna with open-loop inverted triangular-shaped slot for WLAN band filtering
Published 2015“…The notch band frequency is determined by physical parameters defining the TSS that allows fine control of the notch's location. The proposed antenna also possesses a flat gain response expect at the notched band and occupies a relatively small volume of 25 × 25 × 0.8 mm3 for ease of system integration.…”
Get full text
Article -
592
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
593
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
594
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
595
Characterization and solvent stability of strep-tagged purified recombinant lipase from thermostable and solvent tolerant Bacillus sp. strain 42.
Published 2009“…Based on solvent stability studies in 30 min pre-incubation in 25% v/v solvents with a shaking rate at 150 strokes per min, the purified Lip 42 showed a different residual activity profiles depending on solvents and temperatures. …”
Get full text
Article -
596
Wear analysis of Silicon Nitride (Si3N4) cutting tool in dry machining of T6061 Aluminium Alloy
Published 2013“…Machining was performed at four different cutting speeds; 292, 388, 518 and 689 m/min using two different cutting parameters (feed rate, f = 0.2 mm/rev, depth of cut, d = 0.1 mm and f = 0.4 mm/rev, d = 0.2 mm). …”
Get full text
Article -
597
Bladder scan vs urethral cathetarization for measurement of immediate post partum bladder volume
Published 2011“…The mean for time interval between bladder scan and catheterization was 3 min(range between 1-8 min). There is a linear relationship between the bladder scan-estimated and catheter bladder volumes (r2=082). …”
Get full text
Get full text
Get full text
Proceeding Paper -
598
Effect of electrical parameters on performance of Cu-TiC mixed ceramic compact electrode in EDM process
Published 2013“…The highest MRR of 9.93mg/min was obtained with the current of 6.5A and pulse duration of 7.5 μs. …”
Get full text
Get full text
Get full text
Proceeding Paper -
599
Extraction and characterization of gelatin from camel skin (potential halal gelatin) and production of gelatin nanoparticles
Published 2020“…Central composite design combined with response surface methodology was used to achieve high gelatin yields under different extraction conditions: temperatures of 40, 60, and 80 °C; pH values of 1, 4, and 7; and extraction times of 0.5, 2.0, and 3.5 min. Maximum gelatin yield from camel skin (29.1%) was achieved at 71.87 °C and pH 5.26 after 2.58 min. …”
Get full text
Get full text
Article -
600