-
301
Oxidative behaviour of four Malaysian edible plant extracts in model and food oil systems
Published 2012“…This was followed by the extracts of Chinese cabbage (80 min), “kucai” (60 min), and “kesom” (40 min). The antioxidative activities of these plants, however, were lower than those of rosemary and sage. …”
Get full text
Article -
302
Bio-fuel-contaminated lubricant and hardening effects on the friction and wear of AISI 1045 steel
Published 1998“…A study has been made on the wear and fiction of hardened AISI 1045 steel using a pi-pin-ondisc type of fiction and wear apparatus. During the investigation the linear pin wear, coe@cient of friction and rise in pin specimen temperature were monitored and wear and fiction curues 'plotted. …”
Get full text
Article -
303
-
304
-
305
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
306
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
307
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
308
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
309
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
310
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
311
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
312
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
313
Enlighten architecture students on environmental design through computer simulation
Published 2013Get full text
Get full text
Proceeding Paper -
314
Investigation of anticancer (breast cancer) activity of Moringa oleifera leaf extracts
Published 2016“…Cell-lines were seeded at 2x105 cells per ml in a 100µl of media (DMEM 90% and serum 10%) per well in 96 well plates. …”
Get full text
Proceeding Paper -
315
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
316
INFLUENCE OF MACHINING PARAMETERS ON TOOL WEAR AND MACHINING PERFORMANCE IN HIGH SPEED DUCTILE MODE END MILLING OF SODA LIME GLASS
Published 2016“…Nevertheless, high speed machining (HSM) may increase the tool wear, especially for the carbide tools used in glass machining. Therefore on line heating of glass surface was carried out to reduce tool wear. …”
Get full text
Monograph -
317
Optimization of extraction process parameters for anti-cancer agent from Solanum Lycopersicum
Published 2011“…The design variables were the extraction time (min), extraction agitation speed (rpm) and solvent composition (%, v/v water/methanol). …”
Get full text
Book Chapter -
318
Linerboard made from Soda-Anthraquinone (Soda-AQ) treated coconut coir fiber and effect of pulp beating
Published 2015“…Based on chemical analysis, the composition of coir fiber is suitable for the pulping process. Out of nine pulping conditions characterized, a pulping condition of 18% active alkali for 90 min cooking time was chosen. …”
Get full text
Article -
319
A state-of-practice on teaching software verification and validation
Published 2009“…The same online survey was used to obtain data from the Certified Software Test Professional (CSTP) program. Nine universities responded and the data obtained are compared to the data relating to the CSTP program. …”
Get full text
Proceeding Paper -
320
Optimization of double boiling condition for kelulut honey processing using response surface methodology
Published 2018“…Three-level factorial design employed nine runs with duplicates under different combination of temperature (30 – 60 °C) and time (10 – 60 min) was developed. …”
Get full text
Article