Showing 381 - 400 results of 11,163 for search '(((pinna OR owing) OR (five OR ((tinggal OR tangga) OR tinggi))) OR ((spina OR aina) OR ping))', query time: 0.12s Refine Results
  1. 381
  2. 382

    Tool life prediction by response surface methodology in end milling Titanium alloy Ti-6Al-4V using uncoated wc-co inserts by Ginta, Turnad Lenggo, Amin, A. K. M. Nurul, Radzi, Mohd Che Daud, Lajis, Mohd Amri

    Published 2009
    “…This paper presents an approach to establish models for tool life in end milling of titanium alloy Ti–6Al– 4V using uncoated carbide inserts under dry conditions. …”
    Get full text
    Article
  3. 383
  4. 384
  5. 385
  6. 386

    Simulation of haddad surge arrester model on a 132kV overhead transmission line for back flashover analysis using Alternative Transient Program (ATP) by Hassan, Mahadi

    Published 2015
    “…This study modelled a 132kV overhead transmission line for back flashover pattern by using ATP/EMTP software before and after implement the Haddad Surge Arrester Model. …”
    Get full text
    Get full text
    Thesis
  7. 387

    Penghasilan manual rjngkas penggunaan alat Total Station Sokkia Set5f dan Perisian Sdr Mapping & Design untuk automasi ukur topografi by Bagu, Pitus @ Vitus

    Published 2002
    “…Projek ini dilaksanakan untuk menghasilkan manual ringkas penggunaan alat Total Station Sokkia SET5F dan Perisian SDR Mapping & Design dalam menghasilkan pelan topografi yang lengkap mengikut konsep field to finish. …”
    Get full text
    Get full text
    Get full text
    Thesis
  8. 388

    Tool life prediction by response surface methodology in end milling titanium alloy Ti-6A1-4V using uncoated WC-Co inserts by Turnad L., Ginta, A.K.M., Nurul Amin, H.C.D., Mohd. Radzi, Mohd. Amri, Lajis

    Published 2009
    “…This paper presents an approach to establish models for tool life in end milling of titanium alloy Ti–6Al– 4V using uncoated carbide inserts under dry conditions. …”
    Get full text
    Article
  9. 389

    Comparison of surface roughness in end milling of titanium alloy Ti-6Al-4V using uncoated WC-Co and PCD inserts through generation of models by Ginta, Turnad Lenggo, Amin, A. K. M. Nurul, Ishtiyaq, M. H.

    Published 2011
    “…When machining Ti-6Al-4V, conventional tools wear rapidly because the poor thermal conductivity of titanium alloys resulting in higher cutting temperature closer to the cutting edge. …”
    Get full text
    Book Chapter
  10. 390

    IVF-ICSI split insemination reveals those cases of unexplained infertility benefitting from ICSI even when the DNA Fragmentation index is reduced to 15% or even 5% by Mustafa, Kamarul Bahyah, Yovich, John L, Marjanovich, Nicole, Yovich, Steven J

    Published 2016
    “…Conclusions IVF-ICSI split insemination can reveal those cases which will benefit from ICSI even where semen parameters and DFI are normal; however if the DFI is reduced to a 15% cut-off level, the rate of CFF will be minimized, but not completely excluded, even at 5%..…”
    Get full text
    Article
  11. 391
  12. 392
  13. 393

    On iterative low-complexity algorithm for optimal antenna selection and joint transmit power allocation under impact pilot contamination in downlink 5g massive MIMO systems by Mohammed Ahmed, Adeeb Ali

    Published 2020
    “…The proposed low- complexity iterative algorithm achieved the best maximal EE according Fig. 6.5 in chapter 6, which was 95 Mbits/j, resulted from the large number of antennas at the BS, when the transmit power was and transmit antennas was = 100 and user was = 20. …”
    Get full text
    Get full text
    Get full text
    Thesis
  14. 394
  15. 395

    Hajj pilgrims tracking and monitoring system by Mantoro, Teddy, Ayu, Media Anugerah, , Md. Akhtaruzzaman, Mahmud, Murni

    Published 2011
    Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
    Get full text
    Book Chapter
  16. 396

    The significance Of pilgrimage (Hajj) in a muslim’s religious and social life by Yousif, Ahmad

    Published 2012
    Subjects: “…BP176 The five duties of a Moslem. Pillars of Islam…”
    Get full text
    Article
  17. 397
  18. 398
  19. 399
  20. 400