-
281
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
282
Enrichment of fruit wastes with white rot fungi under submerged state bioconversion
Published 2013“…On Banana and Pineapple (BPin) the protein content were recorded as18.05 and 15.75 mg/g, which was higher than Papaya and Pineapple (PinPw) and Banana and Papaya (BPw)composite. M6 has 15.4 and 9.78 mg/g on BPinPw, 13.84 and 13.59 mg/g on BPw, 20.82, and 22.97 mg/g on BPin and 18.29 and 11.59 mg/g on PinPw. …”
Get full text
Proceeding Paper -
283
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
284
-
285
-
286
Development of remote operability CNC milling
Published 2010“…Attachment consists of three main equipments; material indexing device, Sub clamp with pin and vise index…”
Get full text
Proceeding Paper -
287
The system architecture of E-braille by using the microcontroller and external controller unit
Published 2016“…This refreshable braille cell can refresh the character. The pin for each braille cell is controlled by using piezoelectric bimorph. …”
Get full text
Get full text
Article -
288
-
289
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
290
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
291
Development of a low cost lapping process
Published 2009“…Thus it is not unusual to find it difficult to fine finish small area of planar surfaces and attain high degree of flatness on the finished surfaces. …”
Get full text
Proceeding Paper -
292
-
293
-
294
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
295
Ceramic hollow fibre catalytic converters for automotive emissions control
Published 2023Get full text
Thesis -
296
PCR-based chromosome walking: the SFR 3 case
Published 2006“…Eleven new PCR markers had been designed to fine map the gene. Roughly 557 F2 plants tested in these experiments and 38 lines were then used in the fine mapping experiments. …”
Get full text
Article -
297
Optimizing tapered microfiber sensor design and simulation
Published 2016“…The simulation shows that the profile of the sensor can be fine-tuned by changing the tapering ratio of the waist and the length of the taper in order to obtain high performance, ultra-high-resolution evanescent field sensor. …”
Get full text
Article -
298
Histopathological effects of Eurycoma Longifolia jack extract (tongkat ali) on the prostate of rats
Published 2013“…However, although very widely used, it’s possible adverse effects are poorly studied .The objective of this study is to find out if there are any pathological changes that occur in the prostate of rats due to consumption of E.L. root extract. …”
Get full text
Article -
299
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
300
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article