-
5021
Evaluation of antimicrobial activity exploration of the leaves extracts of Borreria articularis (Linn. F.)
Published 2013“…The pure compound, 6-methyl-5-cyclodecen-1-ol, exhibited good antimicrobial activity against all the pathogens tested. …”
Get full text
Article -
5022
Anti-inflammatory and antioxidant properties of unripe papaya extract in an excision wound model
Published 2015“…Materials and methods: Rat excision wounds were topically treated twice/day with 20 μL of PE (5 mg extract/mL), 0.5 μg Se2+ added PE (PES), or 100 μM Zn2+ added PE (PEZ). …”
Get full text
Get full text
Article -
5023
Strength and heat emissions performance of high strength concrete containing fine metakaolin & palm oil fuel ash as partial cement replacement
Published 2024“…Additionally, it is found that the exact amount of 20% FMK and 5% POFA enables concrete to be reduced to 5.54% in peak temperature compared to OPC concrete. …”
Get full text
Conference or Workshop Item -
5024
The performance of removal phosphorus
Published 2020“…Municipal wastewaters comprehend from 5 to 20 mg/L of total phosphorus, of which 1-5 mg/l are organic and the rest are inorganic. …”
Get full text
Book Section -
5025
Characteristic of renewable polymer incorporated with stabilizer to characterize the endurance to ultra voilet irradiation exposure
Published 2016“…Meanwhile, the damping property of 10 % and 5 % TiO2 filler loading (RFC10 and CRC5) gives maximum values of 0.5 and 0.6 respectively with increasing of UV irradiation exposure time. …”
Get full text
Get full text
Get full text
Thesis -
5026
Batch process of mercury (II) removal using CNTs grown on GACs
Published 2011“…It was found that the optimal condition for mercury (II) ions adsorption occurred at adsorbent dosage of 5 mg, pH value of 5, contact time of 120 minutes and agitation speed of 150 rpm with a value of 0.031 mg/L residual amount.…”
Get full text
Proceeding Paper -
5027
Fabrication of biodegradable composite – an implication of plasticizer
Published 2010“…The percentage is varied from 5% to 40% for fiber and for plasticizer it is 5% to 20%. …”
Get full text
Proceeding Paper -
5028
The IIUM low speed wind tunnel
Published 2008“…The new IIUM low speed tunnel is of a closed-loop type having a test section of 1.5m × 2.3m × 6m and a maximum speed of 50 m/s. This paper describes measurement results for initial calibration and flow characteristics of this newly constructed wind tunnel. …”
Get full text
Proceeding Paper -
5029
Flow field characteristics of the IIUM low speed wind tunnel
Published 2008“…The new IIUM low speed tunnel is of a closed-loop type having a test section of 1.5m × 2.3m × 6m and a maximum speed of 50 m/s. …”
Get full text
Proceeding Paper -
5030
Autonomy in language learning
Published 2012“…The samples were 179 students ranging from level 4-5 and of all specializations at the university. …”
Get full text
Article -
5031
Focused ion beam machining of silicon
Published 2002“…A surface roughness in the range of 2-5 nm was achieved, and was found to be linearly dependent on the pixel spacing. © 2002 Elsevier Science B.V. …”
Get full text
Article -
5032
Crystal controlled CMOS oscillator for 13.56 MHz RFID reader
Published 2013“…The computer-generated phase noise is showed -139.5 dBc/Hz at offset of 10 kHz and the power dissipation is 1.25 mW at power supply 2.2V.…”
Get full text
Article -
5033
Effects of gamma irradiation on microbial of white sandwich bread
Published 2016“…Three different brands were irradiated using gamma radiation doses of 0.0, 0.2, 0.3, 0.4 and 0.5 kGy. Results show that 0.2 to 0.5 kGy gamma radiation exposure to the bread has the potential of eliminating or at least minimizing the ecology of spoilage-causing microorganisms in the bread. …”
Get full text
Article -
5034
Amalgamation of metamaterial and SIW technologies for realizing wide-bandwidth and high-radiation properties of on-chip antennas for application in packaging of terahertz component...
Published 2019“…The on-chip antenna is shown to have an average impedance match, gain, and efficiency parameters of -35dB, 8.5dBi, and 67.5%, respectively, over a wide frequency range of 0.20-0.22 THz.…”
Get full text
Conference or Workshop Item -
5035
Effect of multiple extrusions and influence of PP contamination on the thermal characteristics of bottle grade recycled PET
Published 2015“…The thermal characteristics of bottle grade recycled PET pellets contaminated with 5% PP prepared by multiple extrusions were studied by differential scanning calorimetry (DSC) at constant heating rate of 10 degrees C/min for various extrusion cycles. …”
Get full text
Article -
5036
Letter from J O'Connor to T J Hickey
Published 1939“…Manuscript letter, written on 'Lancaster Court Hotel' headed notepaper, enquiring about the presence of undesirable elements in the Anti-Partition League. Dated 5 March 1939.…”
Get full text
Get full text
Correspondence -
5037
CHARACTERISATION AND AREA-SPECIFIC RESISTANCE ANALYSIS OF BARIUM STRONTIUM COBALT FERRITE - SAMARIUM DOPED CERIA CARBONATE - ARGENTUM FOR SOLID OXIDE FUEL CELLS
Published 2023“…The ASR value drops in the BSCF-SDCCAg 3 wt% sample while increasing in the BSCF-SDCC-Ag 5 wt% sample. Apparently, when the temperature is set to high, the ASR value is inconsistent. …”
Get full text
Article -
5038
-
5039
Experimental and simulation study on the effect of geometrical and flow parameters for combined-hole film cooling
Published 2016“…In the case of M = 1.0 and M = 1.5, PoD = 0.0, LoD = 3.5, 1 / 2 = -45o /+45o and PoD = 0.0, LoD = 2.5, 1 / 2 = -45o /+30o are the best configurations based on the overall performance of film cooling.…”
Get full text
Get full text
Get full text
Thesis -
5040
Assessing low thermal conductivity of bricks which contain rice husk, corn cob and waste tea as an additive material
Published 2017“…The percentage of RH, WT and CC used are 2.5%, 5%, 7.5% and 10%. Standard size of fired clay brick are 215 mm x 102.5 mm x 65 mm. …”
Get full text
Get full text
Get full text
Thesis