Physical and mechanical properties of Thermoplastic Natural Rubber (TPNR) nanocomposites by Hassan, Noor Azlina, Hassan, Norita, Ahmad, Sahrim, Rasid, Rozaidi, Anuar, Hazleen, Bonnia, Noor Najmi, Surip, Siti Norasmah

“…Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). …”
Get full text

Investigation of burr in high speed microdrilling by Ali, Mohammad Yeakub, Mohamed, Abd. Rahman, Fadila, N., Hannah, N.

“…The desirability of getting the minimum burr height is72% and the optimum parameters are 30000 rpm spindle speed and 0.2 mm/min feed rate.…”
Get full text

Tool life in high speed turning with negative rake angle by Adesta, Erry Yulian Triblas, Al Hazza, Muataz Hazza Faizi

“…The present work studies some aspects of turning process applied on mild steel using cermets tools at high speed cutting (1000mm/min) by using negative rake angle (90 to 12). The influence of increasing the cutting speed and negative rake angle on flank tool wear, cutting force, feeding forces and tool temperature were analyzed. …”
Get full text

Cooling of motorcyclist helmet with thermoelectric module by Hrairi, Meftah, Abdullah, Abdullah F., Ahmed, Mirghani Ishak

“…The numerical and experimental results showed a good agreement and indicated that the temperature inside the helmet was reduced from 25.5°C to 19.3°C in approximately 6 min.…”
Get full text

Pembangunan budaya kualiti dalam firma pembinaan by Wan Mahmood, Wan Yusoff

Get full text

Contributing cost variation factors in highway projects by Sohu, Samiullah, Abdullah, Abd Halid, Nagapan, Sasitharan, Ahmed Jhatial, Ashfaque, Tahir, Muhammed

“…Cost overrun or cost variation overrun is the main problem in the construction of highway projects in Sindh Province of Pakistan. …”
Get full text

Total quality management (TQM): decision making process model at planning phase for housing development in Malaysia by Mohd Sofberi, Nurul Atiqah, Zainal, Rozlin, Ahmad, Md Fauzi

“…The main aim of this study is to develop a process model for decision making in the planning phase of housing development in Malaysia. …”
Get full text

Synthesis and characterizations of composite based on cu2o zno-polyaniline for removal of Conco Red Dye by Mohammed, Abdussamad Mukhtar

Get full text

Effect of intrapartum pethidine on the neonatal outcome: is it duration related? by Abdulwahab, Dalia F, Husien, Roziah, Busurerah, Ruqaiah, Awang, Mokhtar, Ismail, Rozihan

“…All neonates delivered with good Apgar Score (AS), 8 at 1 minute and 9 at 5 minute except 1 with AS of 5 at 1 min and 7 at 5 min which delivered more than 4 hours after pethidine. …”
Get full text
Get full text
Get full text

Optimization of the cordycepin production by cordyceps militaris in submerged culture by Soltani, Mohammad

Get full text

Nanoencapsulation of alpha-tocopherol via microwave heating technique by Mohamad, Siti Nur Hidayah

Get full text

Photocatalytic dual layer hollow fiber membrane for colour pigment degradation of aerobically treated palm oil mill effluent by Subramaniam, Mahesan Naidu

Get full text

Olahan air sisa pusat penyembelihan ayam menggunakan elektrod keluli tahan karat dan aluminum melalui proses gabungan elektro-penggumpalan dan pengelompokan dan penggumpalan dengan... by Sakury, Khairudin

“…Nilai optimum ketumpatan arus elektrik, jarak antara elektrod, pH awalan, masa tindak balas dan masa enapan masing-masing adalah 25 A/m2, 5 cm, 5, 75 min dan 40 min. Manakala, peratusan penyingkiran yang diperolehi bagi COD, SS, NH3-N, warna dan kekeruhan masing-masing adalah 90.03%, 94.46%, 62.03%, 95.68% dan 94.96%. …”
Get full text
Get full text
Get full text

Optimization of extraction process parameters for anti-cancer agent from Solanum Lycopersicum by Amid, Azura, Ahmad, Abdul Aziz, Ahmad Raus, Raha

“…The design variables were the extraction time (min), extraction agitation speed (rpm) and solvent composition (%, v/v water/methanol). …”
Get full text

Investigation of the anti-wear characteristics of palm oil methyl ester using a four-ball tribometer test by Maleque, Md. Abdul, Masjuki, H.H.

“…A conventional four-ball wear testing machine with different loads was used at 1500 rev miny1 and a test duration of 1 min at ambient room temperature (approximately 28 8C). …”
Get full text

Design and simulation of a thermoelectric cooling system for motorcyclist helmet by Hrairi, Meftah, Abdullah, Abdullah F., Ahmed, Mirghani Ishak

“…The numerical and experimental results showed a good agreement and indicated that the temperature inside the helmet was reduced from 25.5 °C to 19.3 °C in approximately 6 min.…”
Get full text
Get full text

Optimized neural network model for a potato storage system by Abdulquadri Oluwo, Adeyinka, Khan, Md. Raisuddin, Salami, Momoh Jimoh Emiyoka

“…In comparison to a previous study, where the network was based on the min-max method of normalization, the network provided a better representation of the storage process. …”
Get full text

إطلالة على فن المسرح العربي والملايوي الحديث (Itlalah 'ala fann al-masrah al-'Arabi wa-al-Malayuwiy al-hadith) by Yunus, Noraini, Ahmad H.Osman, Rahmah

Get full text

Experimental study of cutting parameter for drilling on fabric carbon/epoxy composite laminates by Abd Halim, Nor Farah Huda, , Afzeri, Aminanda, Yulfian

“…This study is mainly about the drilling of carbon-epoxy laminates. …”
Get full text

Parametric and kinetic studies of microwave–assisted pyroligneous acid from oil palm fiber by Abas, Fatimatul Zaharah

Get full text