Modelling and simulation of 2d aluminium-doped silicene transport properties in field-effect transistors by Chuan, Mu Wen

Get full text

Metamaterial based ultra-wideband antennas for portable wireless applications by Alibakhshikenari, Mohammad, Naser-Moghadasi, Mohammad, Sadeghzadeh, Ramazan Ali, Virdee, Bal Singh, Limiti, Ernesto

“…Various approaches have been reported to reduce the physical size of RF antennas including using high permittivity substrates, shorting pins, reactive components, and more recently, metamaterials (MTM) based on composite right-/left-handed transmission-lines (CRLH-TLs). …”
Get full text

Jujurlah dalam perkhidmatan by Abd Rahman, Saodah

Get full text

Puasa membentuk jiwa suci by Abd Rahman, Saodah

Get full text

Kemunculan Neo-Kharijites by Abd Rahman, Saodah

Get full text

Synthesis, characterization and catalytic activity of copper thiosemicarbazone complexes and their oxides in the reduction of nitroaromatic compounds by Handy, Omar Abdullahi Wafudu

Get full text

Fabrication of micromold cavity for microreplication: A review by Ali, Mohammad Yeakub, Khan, Ahsan Ali, Mehfuz, R., Aishah, S., Hayati, N., Hajar, N.

“…In the later stage direct fabrication techniques such as focused ion beam, micro electro discharge machining, laser micromachining, tool based micromilling, etc., become cost effective and popular. …”
Get full text

Hot embossing and injection molding of three-dimensional microcomponents by Ali, Mohammad Yeakub, Ngoi, B. K. A., Hung, N. P., Yuan, S., Lee, C.P.

“…The microcavities were fabricated by focused ion beam (FIB) sputtering. Microgears, microgear trains, microlenses etc. were successfully replicated from polymers. …”
Get full text

Data redundancy reduction using sensitivity analysis method for machine-learning-based battery management system by Mustaza, Muhammad Syafiq Anwar

“…The novel approach analyzes the sensitivity of lithium-ion battery model parameters towards their discharge performances. …”
Get full text
Get full text
Get full text

Ballistic impact fracture behaviour of continuous fibre reinforced al-matrix composites by Ali, Al-Hamdan, Nimir, Yassin Lutfi Mahmud, Mustafa, Ramadan J.

“…The materials response under high energy impact loads was studied using a gas gun. The projectiles were pins 1.2-1.5 mm in diameter and weighing 0.347-0.435 g. …”
Get full text

Fabrication of silicon nanopillar sheet for Cell Culture Dish by Ali, Mohammad Yeakub, Mohd Fuad, Nurul Hajar

“…This paper discusses the fabrication of nanopillars using focused ion beam (FIB) sputtering. A 25 keV Ga+ FIB was used to machine the nanopillars. …”
Get full text

Fabrication of Silicon Nanopillar Sheet for Cell Culture Dish by Ali, Mohammad Yeakub, Mohd Fuad, Nurul Hajar

“…This paper discusses the fabrication of nanopillars using focused ion beam (FIB) sputtering. A 25 keV Ga+ FIB was used to machine the nanopillars. …”
Get full text

Antioxidant study of pulp and peel of dragon fruits: A comparative study by Ruzlan, Nurliyana, Kamarudin, Kamarul Rahim, Syed Osman Idid, Syed Zahir Idid, Mohamed Rehan, Aisyah, Koya, Mustapha Suleiman

“…Furthermore, both peels and pulps of Hylocereus species showed weak metal ion chelating effect as compared to EDTA. It was found that pulp of both species showed a significant secondary antioxidant effect instead of primary antioxidant effect. …”
Get full text

Antioxidant study of garlic and red onion: a comparative study by Che Othman, Siti Fairuz, Syed Osman Idid, Syed Zahir Idid, Koya, Mustapha Suleiman, Mohamed Rehan, Aisyah, Kamarudin, Kamarul Rahim

“…Furthermore, both the Allium samples show slightly higher ion chelating effect than BHA (i.e. 43.14 ± 1.07%) but lower than EDTA (i.e. 97.9 ± 0.07%). …”
Get full text

Modeling of a turning tool holder with finite elements and simulation of its free vibration frequencies by Jaafar, Israd Hakim, Shaik Dawood, Mohd. Sultan Ibrahim, Amin, A. K. M. Nurul, Shah, Qasim Hussain

“…This latter difference is unavoidable, due to the experimental test setup whereby the tool holder is clamped within the fixture with only 2 pins as opposed to the more rigid boundary condition applied to the finite element model, whereby the whole holder length within the carriage is rigidly supported at the element nodes. …”
Get full text

LC-MS-MS development and validation for simultaneous quantitation of metformin, glimepiride and pioglitazone in human plasma and its application to a bioequivalence study by Sengupta, Pinaki, Bhaumik, Uttam, Ghosh, Animesh, Sarkar, Amlan Kanti, Chatterjee, Bappaditya, Bose, Anirbandeep, Pal, Tapan Kumar

“…Quantitation was performed on a triple quadrupole mass spectrometer employing electrospray ionization technique, operating in multiple reaction monitoring and positive ion mode. Inter-batch and intra-batch coefficient of variation across four validation runs for the quality control samples was less than 7%. …”
Get full text

Further investigations of the prevulcanization of natural rubber latex by Loh, Aaron Chun-Pong

“…The faster rate of reaction in latex prevulcanizatIon is attributed to the presence of the aqueous phase which acts as a medium for the dissolution of ZDBC and sulphur, and provides a suitable environment for the two vulcanizing ingredients to react to form the active sulphurating agent. …”
Get full text

Preparation, characterization and application of Zeolite-Y (Na-Y) for water filtration by Rahman, Md. Mokhlesur, M. B., Awang, A. M., Yusof

“…In this study the acid treated rice husk ash was used as SiO2 source in the preparation of zeolite Y, a medium siliceous zeolite used as an ion exchangers in water treatment process. Purity, pore size distribution, FT-IR and SEM micrographs of treated and non-treated samples are presented. …”
Get full text

Development of Microreplication Process - Micromolding by Yuan, Shu, Hung, NguyenPhu, Ngoi, Bryan Kok Ann, Ali, Mohammad Yeakub

“…It included modifying a conventional molding machine, developing a thermal control unit to control the mold temperature, and developing a vacuum unit to evacuate the microcavity before filling it with plastic melt. Focused ion beam sputtering, a maskless patterning of material, was used to fabricate a microcavity that was then used as a mold insert. …”
Get full text

Surface roughness of sputtered silicon. II. Model verification by Ali, Mohammad Yeakub, Hung, NguyenPhu

“…The beam shape and its significant level of intensity were determined first by measuring the topography of craters sputtered by focused ion beam (FIB). Then the beam function was generated for various combinations of beam parameters. …”
Get full text