Influence of mesh sizes and orientations on expanded aluminium sheets on tensile performances by Nik Ismail, N A, Roslan, M N, Ismail, A E, El Bakri, H M

“…According to the results of the experiment, specimens with fine mesh have higher tensile stress, which is 44.90 MPa for fine mesh specimens with a 30° orientation, compared to medium and coarse mesh sizes, which have the lowest strength, which is 7.06 MPa for coarse mesh specimens with a 60° orientation. …”
Get full text

Streptokinase After Spinal Anaesthesia. A Case Report by Mohamed, Rozilah @ Abdul Hadi, Mat Nor, Mohd Basri, Osman, Ariff

“…Patients usually present with acute axial spine pain and evolving focal neurological deficits. …”
Get full text

The Exploration of the Characteristics of Concrete Incorporating Ultrafine Coal Bottom Ash and Spent Garnet by Wan Chik, Wan Muhammad Eddie Khusyairi, Mokhatar, Shahrul Niza, Othman, Nor Hazurina, AAlbshir Budiea, Ahmed Mokhtar, Muthusamy, Khairunisa

“…Two such materials, ultrafine coal bottom ash (uCBA) and spent garnet (SG), have shown potential as substitutes for cement and fine aggregate, respectively. This research examines the effectiveness of uCBA as a partial replacement for cement and SG as a partial replacement for fine aggregate in concrete, at varying levels of 3%, 6%, and 9% for uCBA and 10%, 20%, and 30% for SG. …”
Get full text

The Exploration of the Characteristics of Concrete Incorporating Ultrafine Coal Bottom Ash and Spent Garnet by Wan Chik, Wan Muhammad Eddie Khusyairi, Mokhatar, Shahrul Niza, Othman, Nor Hazurina, Albshir Budiea, Ahmed Mokhtar, Muthusamy, Khairunisa

“…Two such materials, ultrafine coal bottom ash (uCBA) and spent garnet (SG), have shown potential as substitutes for cement and fine aggregate, respectively. This research examines the effectiveness of uCBA as a partial replacement for cement and SG as a partial replacement for fine aggregate in concrete, at varying levels of 3%, 6%, and 9% for uCBA and 10%, 20%, and 30% for SG. …”
Get full text

A novel method for chatter control and improvement of surface finish in end milling by Amin, A. K. M. Nurul, Sulaiman, Syidatul Akma

“…The fixture design can be adjusted to suit any spindle diameter and the method can be applied to any vertical milling machine or machining center. …”
Get full text

Development of a mathematical model for the prediction of surface roughness in end milling of stainless steel SS 304 by Amin, A. K. M. Nurul, Mahmoud, Asif

“…Kaye et al [4] used response surface methodology in predicting tool flank wear using spindle speed change. A unique model has been developed which predicts tool flank wear, based on the spindle speed change, provided the initial flank wear at the beginning of the normal cutting stage is known. …”
Get full text

Primary plasma cell leukemia presented as progressive paraplegia: a case report by Hasmoni, Mohamed Hadzri, Abdul Wahid, Fadilah, Cheong, Soon Keng

“…The patient presented with paraparesis which progressively worsened to paraplegia. MRI of the spine showed an extradural mass causing cord compression and multiple bony erosions from soft tissue masses. …”
Get full text

Role of cricothyrotomy and percutaneous tracheostomy in airway management by Mat Nor, Mohd Basri

“…Established contraindications against PCT are unstable fractures of cervical spine, severe local infection of anterior neck and uncontrolled coagulopathy. …”
Get full text
Get full text

Effect of solution treatment on high tempreature oxidation of Fe-33Ni-19Cr alloys Fe-40Ni-24Cr alloys. by Parimin, Noraziana

Get full text

Investigation of the influence of different parameters on chatter arising during metal cutting process by Amin, A. K. M. Nurul, Khaled, Khalil

“…At critical range of cutting speed, metal cutting process is accompanied with chatter, when either the job and spindle or the tool bit holder vibrate with their natural frequencies. …”
Get full text

Performance evaluation of drilling tools during machining plain Carbon Fiber Reinforced Polymer (CFRP) by Konneh, Mohamed, Zaini, Mohamad Hamzi

“…It was observed that minimal delamination at entry and exit is achieved when using TIAlN at high spindle speed and feed.…”
Get full text

Alternative sweetener from curculigo fruits by Jalaluddin, Hazwan, Karim, Izz Qayyum, Mohammad Nor, Nurhanani, Senin, Zulkifli

“…Finally, the dried fruits were blended in order to get a fine powder. Curculin is a sweet protein with a taste-modifying activity of converting sourness to sweetness. …”
Get full text

Effect of river indus sand on concrete tensile strength by Lakhiar, Muhammad Tahir, Mohamad, Noridah, Shaikh, Muhammad Abu Bakar, Ahmed Vighio, Anees, Ahmed Jhatial, Ashfaque, Abdul Samad, Abdul Aziz

“…In the development of Pakistan construction industry, the utilization of River Indus sand in concrete as fine aggregate has expanded tremendously. The aim of this research is to study the effect of Indus River sand on the tensile strength of various grades of concrete when it is utilized as fine aggregate. …”
Get full text

Modeling for surface roughness in end-milling of Titanium alloy Ti-6Al-4V using uncoated WC-Co inserts by Amin, A. K. M. Nurul, Ginta, Turnad Lenggo, Ishtiyaq, M. H.

“…Kaye et al [7] used response surface methodology in predicting tool flank wear using spindle speed change. A unique model has been developed which predicts tool flank wear, based on the spindle speed change,provided the initial flank wear at the beginning of the normal cutting stage is known. …”
Get full text

Development and performance evaluation of an ultra precision ELID grinding machine by Saleh, Tanveer, Rahman, M. Sazedur, Lim, H.S., Rahman, M.

“…The machine is a five-axis machine, which includes three conventional linear axes (X, Y and Z) and a spindle axis. On top, another rotational axis has been included to assist the aspheric/spherical lens grinding. …”
Get full text

Application of taguchi and box-behnken designs for surface roughness in precision grinding of silicon by Alao, Abdul-Raheed, Konneh, Mohamed

“…Taguchi method was used to study the effect and optimisation of grinding parameters while Box-Behnken method was utilised to develop a mathematical model relating the average surface roughness to the grinding parameters, depth of cut, feed rate and spindle speed. An orthogonal array (OA), the signal-to-noise (S/N) ratio, and the analysis of variance were employed to find the minimal surface roughness. …”
Get full text

Characteristics of ferrocement sandwich aerated concrete wall elements incorporating pozzolanic waste materials by Navaz, Taha Mehman

Get full text

A rare case of monostotic spinal fibrous dysplasia mimicking solitary metastatic lesion of thyroid carcinoma by Sharifudin, Mohd Ariff, Zakaria@Mohamad, Zamzuri, Awang, Mohamed Saufi, Mohamed Amin, Mohamed Azril, Abd. Aziz, Azian

“…A case of a 53-year-old lady who presented with an 8 months history of pain in the thoracic spine region with paraparesis is discussed. She had a history of papillary thyroid carcinoma and had undergone total thyroidectomy one year prior to her current problem. …”
Get full text
Get full text

Mechanical Properties of Lightweight Aggregate Concrete Containing Unground Palm Oil Fuel Ash as Partial Sand Replacement by H. Mohd Hanafi, H. Mohd Hanafi, Muthusamy, Khairunisa, Saffuan, W.A., Budiea, A.M.A., Kusbiantoro, A., Nabilla, M., Rafiza, A.R., Błoch, K.

“…This is owing to void filling mechanism and product of pozzolanic reaction due to the fine particles of the ash.…”
Get full text

High speed end milling of silicon using diamond coated tools with air blowing by Amin, A. K. M. Nurul, Khalid, Noor Syairah, Mohd. Nasir, Siti Nurshahida

“…An optimum air blowing pressure and combination of spindle speed, feed and depth of cut has been identified to achieve minimum value of surface roughness and defect free machined surface. …”
Get full text