-
341
Annealing Treatment on Homogenous n-TiO2/ZnO Bilayer Thin Film Deposition as Window Layer for p-Cu2O-Based Heterostructure Thin Film
Published 2023“…In this work, n-TiO2/ZnO bilayer thin film was effectively constructed by means of sol-gel spin coating technique in an effort to diminish the electron-hole recombination rate from single-layered thin film. …”
Get full text
Article -
342
Annealing Treatment on Homogenous n-TiO2/ZnO Bilayer Thin Film Deposition as Window Layer for p-Cu2O-Based Heterostructure Thin Film
Published 2023“…In this work, n-TiO2/ZnO bilayer thin film was effectively constructed by means of sol-gel spin coating technique in an effort to diminish the electron-hole recombination rate from single-layered thin film. …”
Get full text
Article -
343
Annealing Treatment on Homogenous n-TiO2/ZnO Bilayer Thin Film Deposition as Window Layer for p-Cu2O-Based Heterostructure Thin Film
Published 2023“…In this work, n-TiO2/ZnO bilayer thin film was effectively constructed by means of sol-gel spin coating technique in an effort to diminish the electron-hole recombination rate from single-layered thin film. …”
Get full text
Article -
344
Effect of calcination temperature on bilayer TiO2/ZnO and ZnO/TiO2 thin films
Published 2018“…Thin films are produced on glass substrate via spin coating method at speed of 3000 rpm and were calcined at different calcination temperatures that are 400 oC, 500 oC, and 600 oC. …”
Get full text
Get full text
Get full text
Thesis -
345
Low-temperature growth of zinc oxide structures on flexible conductive substrate: effect of NaOH and C7H8O9 presence in solgel
Published 2021“…The precursor solutions were spin-coated on the ITO/PET substrate and were dried at room temperature and pre-heated oven at 150°C for 3 minutes. …”
Get full text
Get full text
Get full text
Thesis -
346
Study the performance of porous pavement on urban thermal environment. Part 1: Field observation
Published 2008“…A numerical method was developed to study the thermal characteristics of porous pavement under fine meteorological conditions, which will be discussed in our next effort. …”
Get full text
Proceeding Paper -
347
Structure and function of proteins important in Mycobacterium tuberculosis energy metabolism
Published 2009“…Purification of a GST-tagged construct to eliminate proteolytic degradation and further fine screening is ongoing to obtain better quality crystals for X-ray diffraction. …”
Get full text
Proceeding Paper -
348
Spatial distribution of lead and copper in the bottom sediments of Pahang River estuary, Pahang, Malaysia
Published 2010“…The concentration for both metals increased with the decrease of mean size, suggesting their association with the fine fraction of the sediments.…”
Get full text
Article -
349
Tuning of fuzzy logic controllers by parameter estimation method
Published 1993“…Fuzzy logic controllers (FLC) require fine tuning to match the rules to the membership functions or vice-versa. …”
Get full text
Get full text
Get full text
Get full text
Book Chapter -
350
Aluminium metal matrix composite: improving wear performance through treatment
Published 2011“…The triple particle size (TPS) composite consist of SiC of three different sizes viz., coarse, intermediate and fine. The solution heat treatment was carried out on cast specimens at 540 °C for four hours followed by precipitation treatment. …”
Get full text
Article -
351
Islamic architecture : its philosophy, spiritual significance & some early developments
Published 2009“…Islamic architecture is a fine blend of all these factors which are interwoven with the treads of the belief system, principles, teachings and values of Islam. …”
Get full text
Book -
352
Tendon bioreactor
Published 2016“…The parameters such as frequency, the duration and the strain applied can further fine tune to meet the design requirement. Nevertheless, the optimum function of the bioreactor also relies on the mass transport of the nutrients or the medium circulation. …”
Get full text
Monograph -
353
The use of SEM to investigate the effect of an electron beam on the optically-visible flashover treeing of MgO ceramic
Published 2007“…An SEM may be used not only to observe a surface image but also to provide a fine electron beam for charging an insulator surface simultaneously. …”
Get full text
Article -
354
An SEM flashover: technique to characterize wide band gap insulators
Published 2006“…An SEM may be used not only to observe a surface image but also to provide a fine electron beam for charging an uncoated insulator surface at once. …”
Get full text
Proceeding Paper -
355
CPW-fed printed UWB antenna with open-loop inverted triangular-shaped slot for WLAN band filtering
Published 2015“…The notch band frequency is determined by physical parameters defining the TSS that allows fine control of the notch's location. The proposed antenna also possesses a flat gain response expect at the notched band and occupies a relatively small volume of 25 × 25 × 0.8 mm3 for ease of system integration.…”
Get full text
Article -
356
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
357
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
358
A Convolutional Neural Network Model to Segment Myocardial Infarction from MRI Images
Published 2023“…The layers selection and hyper-parameters fine-tuning were applied before the training phase. …”
Get full text
Article -
359
Effect of heating rates on the microstructure and gas permeation properties of carbon membranes
Published 2018“…A single permeation apparatus was used to determine the gas permeation properties of the membrane at room temperature. Fine turning of the carbonization condition was necessary to obtain the desired permeation properties. …”
Get full text
Article -
360
High speed end milling of single crystal silicon using diamond coated tools
Published 2011“…They study about the effect of the depth of cut, feed rate and spindle speed. Rusnaldy et al. [5] showed that the dominant ductile cutting mode was achieved for Ft/Fc>1.0, which indicates that the thrust force is dominant over the cutting force. …”
Get full text
Book Chapter