-
261
A study on controllable aluminium doped zinc oxide patterning by chemical etching for MEMS application
Published 2017“…This present work reports on the study of controllable aluminium doped zinc oxide (AZO) patterning by chemical etching for MEMS application. The AZO thin film was prepared by RF magnetron sputtering as it is capable of producing uniform thin film at high deposition rates. …”
Get full text
Get full text
Get full text
Article -
262
ANT colony optimization for controller and sensor-actuator location in active vibration control
Published 2013“…This paper discusses on active vibration control of a simply supported thin plate excited and actuated by piezoelectric patches. …”
Get full text
Article -
263
Surface finish prediction models for precision grinding of silicon
Published 2011“…Therefore, this work reports the empirical models developed for surface parameters Ra, Rmax, and Rt with precision grinding parameters, depths of cut, feed rates, and spindle speeds using conventional numerical control machine tools with Box–Behnken design. …”
Get full text
Article -
264
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
265
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
266
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
267
Fabrication of frequency selective structure and evaluation of microwave transmission on energy saving glass
Published 2015“…This energy saving property is achieved by applying a very thin tin oxide (SnO2) coating on one side of the glass. …”
Get full text
Get full text
Get full text
Thesis -
268
Electrodeposition of nanostructure materials
Published 2015“…We are conducting a multi-disciplinary research work that involves development of nanostructured thin films of semiconductors for different applications. …”
Get full text
Book Chapter -
269
Finite element modelling of fixed-fixed end plate attached with vibration absorber
Published 2016“…The present paper investigated the effect of the lightweight dynamic vibration absorber (LDVA) to reduce vibration of thin walled structure. The free and forced vibration response of a rectangular thin plate were performed using finite element method. …”
Get full text
Article -
270
Metasurface for controlling polarization of scattered EM waves
Published 2020“…The dual band metasurface is realized by stacking an array of multiple concentric circular rings. By rotating each array with respect to each other, we can manipulate its impedance at distinct frequencies. …”
Get full text
Conference or Workshop Item -
271
Histopathological effects of Eurycoma Longifolia jack extract (tongkat ali) on the prostate of rats
Published 2013“…However, although very widely used, it’s possible adverse effects are poorly studied .The objective of this study is to find out if there are any pathological changes that occur in the prostate of rats due to consumption of E.L. root extract. …”
Get full text
Article -
272
Study on micro-patterning process of vertically aligned carbon nanotubes (VACNTs)
Published 2016“…A minimum average surface roughness of Ra D 15 nm was achieved with 2000 rpm spindle speed, 1 mm/min bending speed and 1 mm step size.…”
Get full text
Get full text
Get full text
Article -
273
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
274
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
275
Influence of chip serration frequency on chatter formation during end milling of Ti6Al4V
Published 2011“…It has been concluded from these findings that chatter occurs during end milling due to the resonance of the machine tools system component when the frequency of primary serrated teeth formation is approximately equal to the "prominent natural frequency" modes of the system components, which are the two mode frequencies of the VMC machine spindle in this particular case.…”
Get full text
Article -
276
The investigation of chlorpyrifos (Cpy) detection of PEDOT:PSS‑MXene(Ti2CTX)‑BSA‑GO composite using P‑ISFET reduction method
Published 2023“…This is much lower than that when using titanium dioxide (TiO2), which is −1.5 V. Composite thin flms containing Ti2CTX MXene are found to detect Cpy with higher sensitivity compared to thin flms without MXene. …”
Get full text
Article -
277
A zinc–air cell employing a porous zinc electrode fabricated from zinc–graphite-natural biodegradable polymer paste
Published 2002“…In the cell design, a thin agar layer was introduced between the electrode-gelled electrolyte interfaces, resulting in substantially improved cell discharge performance. …”
Get full text
Article -
278
Shielding effectiveness of mesh wire for 50Hz magnetic field
Published 2011“…A wire mesh shield composed of thin conductive wires will influence the behaviour of electromagnetic fields within it. …”
Get full text
Get full text
Get full text
Thesis -
279
Nutritional status of school children aged 6-10 years old in Selangor
Published 2010“…About 11% of the rural school children were within thin and very thin compared to urban school children 6.5%. …”
Get full text
Article -
280
Manufacture of cylinders with axial imperfections
Published 2004“…The report outlines the methodology and procedures used to manufacture the thin walled cylinder with its axial imperfections using a NUM 1060 CNC Lathe machine. …”
Get full text
Thesis