-
101
-
102
Preliminary design of sliding mode controller for angular positional tracking of an aircraft
Published 2009Get full text
Proceeding Paper -
103
-
104
Holocene environmental change in the Scottish Highlands: multi-proxy evidence from blanket peats
Published 1997“…This thesis seeks to investigate the Holocene environmental history of two areas of Northern Scotland with specific reference to the evidence for pine woodland density variations and tree-line dynamics. …”
Get full text
Thesis -
105
-
106
A study on laser engraving process parameters and performance characteristics for wood base materials
Published 2018“…This research presents a study on the parameter of laser engraving on pine wood and WPC materials by using EleksMaker Laser A5-Pro model with low diode laser (500Mw, 405nm wavelength). …”
Get full text
Get full text
Get full text
Thesis -
107
Syringomyelia in pregnancy - is caesarean section the best option for delivery - a case report
Published 2009“…Syringomyelia is a rare neurological disease, which is characterized by the formation of a cyst in the spinal cord. The aetiology of the disease still remains controversial. …”
Get full text
Article -
108
Effect of adding global postural re-education to Kendall exercises for treating asymptomatic forward head posture: a single-blinded randomized controlled trial
Published 2025“…Conclusions: The added effect GPR technique to Kendall exercises significantly improved CVA, CROM, NDI, chest expansion, and spinal mobility in subjects with FHP.…”
Get full text
Article -
109
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
110
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
111
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
112
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
113
Biomedical Analysis of Lateral Lumbar Interbody Fusion (LLIF) Cage for Lumbar Vertebrae
Published 2023“…Objective: To develop the interbody cages implanted between the lumbar vertebrae by evaluating the strength of the bone model and the spinal cage. Materials and methods: In this study, finite element analysis (FEA) was applied using Mechanical Finder software (MF) to develop a 3D spine model lumbar vertebrae of the fourth and fifth lumbar vertebrae (L4 - L5) with various interbody cage designs, including honeycomb and rectilinear patterns with 50%, 70%, and 100% infill densities. …”
Get full text
Article -
114
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis -
115
Multi-Mode Yagi Uda Patch Array Antenna With Non-Linear Inter-Parasitic Element Spacing
Published 2023“…Applying the inter-parasitic element spacing’s optimization and minimizing the switching circuitry using four RF PIN diodes on the parasitic elements have contributed to the gain achievement of more than 7 dBi.…”
Get full text
Article -
116
Analysis re-entrant honeycomb auxetic structure for Lumbar vertebrae using finite element analysis
Published 2024“…Lumbar spinal fusion is a frequent surgical solution among people who are experiencing severe persistent lower back pain. …”
Get full text
Article -
117
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…In the present study, wear behavior of the Fe-C-Si and Fe-C-Al cast irons were investigated using a pin-on-disk type apparatus at room temperature. …”
Get full text
Article -
118
Biomechanical evaluation and new improvement on ankle external fixator
Published 2023Get full text
Thesis -
119
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
120
Biotar ironmaking using wooden biomass and nanoporous iron ore
Published 2009“…In our experiments, three types of iron ores containing different amounts of combined water (CW; 1.6, 3.8, and 9.0 mass %) were first dehydrated at 450 °C to make them porous and then heated with pine tree biomass at 500-600 °C for the gasification and the tar vapor generated was decomposed to deposit carbon within/on the porous ores. …”
Get full text
Article