Showing 1,221 - 1,240 results of 2,996 for search '(((spinned OR (hinge OR bina)) OR line) OR ((pinna OR pinn) OR (peng OR ming)))', query time: 0.18s Refine Results
  1. 1221

    Recovery of 3D shapes from 2D sketches by Liu, Yang

    Published 2013
    “…The objective of this research is to recover 3D freeform surfaces depicted in a single line drawing, with the aim of taking conceptual design sketches and converting them into 3D models. …”
    Get full text
    Thesis
  2. 1222

    Parametric study of gravure printing process for R2R printed electronics by Pua, Suan Tai

    Published 2017
    “…In this study, however, various printing parameters were investigated to establish their effects on printed line width and film thickness, in an attempt to achieve fine line printing resolution over a large printing area. …”
    Get full text
    Final Year Project (FYP)
  3. 1223

    Advancements in Management Science: Applications to Online Retail, Healthcare, and Non-Profit Fundraising by Zhai, Chen Wen (Sabrina)

    Published 2024
    “…Studies on the efficacy of first-line versus second-line and alternative antibiotics for UTI are limited and dated. …”
    Get full text
    Thesis
  4. 1224

    Design of a >500MHz current starving VCO/DLL with low phase noise for digital PWM control by Chua, Dillon Yu Ze

    Published 2023
    “…It typically consist of a voltage controlled delay line, a phase detector. A delay line consists of a chain of delay cells that can be varied to adjust the amount of delay between the output and input signal through the delay line. …”
    Get full text
    Final Year Project (FYP)
  5. 1225
  6. 1226
  7. 1227

    Atomic transistors beyond Moore's law by Li, Haifeng

    Published 2023
    Get full text
    Thesis-Master by Coursework
  8. 1228

    Rapid process modeling of the aerosol jet printing based on gaussian process regression with latin hypercube sampling by Zhang, Haining, Moon, Seung Ki, Ngo, T. H., Tou, J., Bin Mohamed Yusoff, M. A.

    Published 2021
    “…Hence, it is necessary to develop a small data set based machine learning approach to model relationship between the process parameters and the line morphology. In this paper, we propose a rapid process modeling method for AJP process and consider sheath gas flow rate, carrier gas flow rate, stage speed as AJP process parameters, and line width and line roughness as the line morphology. …”
    Get full text
    Journal Article
  9. 1229
  10. 1230

    Recovery of three-dimensional objects from single two-dimensional sketches using cubic corners by Vishnuprasad Venugopalapanicker

    Published 2011
    “…This report describes the work done to recover 3D objects from a single 2D line drawing using theconcept of cubic corner. …”
    Get full text
    Final Year Project (FYP)
  11. 1231
  12. 1232

    Train following model for urban rail transit performance analysis by Saidi, Saeid, Koutsopoulos, Haris N, Wilson, Nigel HM, Zhao, Jinhua

    Published 2024
    “…Based on the model developed, the impacts of factors such as service frequency, headway variations, passenger demand, and initial train delays on line performance (i.e. line throughput and train knock-on delays) are explored. …”
    Get full text
    Article
  13. 1233

    Ultra wideBand indoor position localizaiton by Xu, Jun

    Published 2014
    “…It is specifically the case when line-of-sight (LOS) is absent due to severe blockage. …”
    Get full text
    Thesis
  14. 1234
  15. 1235
  16. 1236
  17. 1237
  18. 1238
  19. 1239
  20. 1240