Flexural buckling behaviour and residual strengths of S700 high strength steel circular hollow section columns after exposure to fire by Koh, Alicia

“…The experimental study which includes the furnace tests, material tests, initial global imperfection measurements, and pin-ended column tests was conducted and reported. …”
Get full text

3D modelling using digital camera by Chong, Yeow Koon.

“…Some other trial targets that we have done includes fire station, NTU N2 building and a three pin plug. More details will be covered in chapter 2 of this report.…”
Get full text

NTU e-bike by Zeng, Wei

“…To support the touchscreen, the expansion board pin configurations are modified according to the schematic connections, also the kernel changed to detect the GPS device, the Éclair system can‟t get GPS information directly since a hardware abstraction layer (HAL) is needed for interacting between the Android framework and the kernel. …”
Get full text

CRISPR-DBA: a deep learning framework for uncertainty quantification of CRISPR off-target activities by Cao, X, Minary, P

HCI for Cybersecurity, Privacy and Trust : Third International Conference, HCI-CPT 2021, Held as Part of the 23rd HCI International Conference, HCII 2021, Virtual Event, July 24-29... by HCI for Cybersecurity, Privacy and Trust (Conference) (3rd : 2021 : Online) 643239, Moallem, Abbas, editor 630807

Application of low frequency noise in the study of VLSI electromigration by Lim, Shin Yeh.

Get full text

Integrated vision functions for the guidance of smart vehicle by Wong, Swee Meng.

Get full text

6G Wireless : The Communication Paradigm Beyond 2030 / by Tariq, Faisal, editor 622951, Muhammad, Khandaker, editor 655110, Imran, Ansari Shafique, editor 655111

Get full text
Get full text

Mechatronics design and real time control of a mobile robot with passive involute shape auxiliary devices by Zhou, Yuan

Get full text

Kinematic analysis and optimal design of three-legged reconfigurable parallel manipulators by Anjan Kumar Dash

Get full text

Laser metal deposition of low carbon 410L stainless steel and heat treatment by Zhai, Wengang, Wu, Naien, Zhou, Wei

“…The yield strength is 601.9 MPa for as-built condition and 930.6 MPa for heat-treated condition (1000 °C/10 min); the ultimate tensile strength (UTS) is 923.0 MPa for as-built condition and 1101.5 MPa for the heat-treated condition (1000 °C/10 min); the elongation is 17.7% for as-built condition and 15.1% for the heat-treated condition (1000 °C/10 min). …”
Get full text

Dose response effect of carbohydrate mouth rinse on 10 km running time trial by Muhammad Saufy Abdul Karim

“…Results: No significant difference (p = .441) in 10 km running time trial were observed between 6.4% CHO [mean 63.83 (SD 11) min] and 15% CHO [mean 65.91 (SD 13.36) min]. No significant difference were found in HR (p = .440) between 6.4% CHO [mean 162 (SD 7) beats/min] and 15% CHO [mean 158 (SD 13) beats/min]. …”
Get full text

Pengetahuan, Sikap dan Praktis (KAP) Komuniti Pekebun Kecil Koko (KPKK) berkaitan Malaysian Good Agricultural Practices (MyGAP) by Noviatin Syarifuddin, Jasmin Arif Shah, Asnarulkhadi Abu Samah, Nik Ahmad Sufian Burhan

“…Tahap amalan pertanian baik (APB) menunjukkan nilai min tertinggi oleh praktis (min 4.20). Diikuti, dengan tahap sikap (min 4.08) dan tahap pengetahuan (min 4.01) oleh KPKK. …”
Get full text

Mechanical properties of pultruded Kenaf fibre-reinforced vinyl ester composites by Abd Manab, Mohd Fairuz

“…The investigation of the effect of pulling speed on the mechanical properties of pultruded kenaf composites shows the optimal pulling speed for tensile strength and compressive strength is 0.3 m/min, tensile modulus 0.1 m/min, flexural strength 0.4, flexural modulus 0.2 m/min. …”
Get full text

Influence of machining parameters and tool geometry on tool wear during cobalt chromium-molybdenum micro drilling by Abdul Patar, Mohd. Affifudin, Suhaimi, Mohd. Azlan, Sharif, Safian, Amrifan S. Mohruni, Amrifan S. Mohruni, Hisam, Muhammad Juzaili, Shaharum, Mohd. Sallehuddin

“…The cutting speeds of 50 m/min, 65 m/min, and 80 m/min were varied. A total of 11 runs were performed, with each run consisting of drilling 30 holes. …”
Get full text

Jurong Island groundwater study : hydrological and hydraulic investigations by Wong, Shao Jie.

“…Subsequently, a series of well yields in different well diameters (2m to 2.2m) as well as RD (Min RD = 221.8 m), the ridge radiuses are estimated based on conservative natural infiltration before sea water intrusion occurs. …”
Get full text

Analog smart I/O pads by Tan, Shyue Mei.

“…ESD is an increasingly significant problem in integrated circuit design as increasing pin counts and faster circuit speeds compound the need for more and better reliable ESD protection. …”
Get full text

Tribological properties of wax microcapsule modified polymers by Ang, Ping Lon

“…The tribology test uses the Pin-On-Disk wear test method and the default tribometer settings used in this project were set at 2000m sliding distance, 40cm/s linear speed and 3N linear load. …”
Get full text

Effect of emulsion temperature on physical properties of palm oil‐based margarine by Miskandar, M. S., Che Man, Y. B., Yusoff, M. S. A., Abdul Rahman, R.

“…The emulsion temperatures studied were 40, 45, and 50°C, with other parameters such as emulsion flow rates, tube cooler temperature, and pin rotor speed kept constant. The SFC developed during processing and storage at 28°C was measured to evaluate the quality of margarine. …”
Get full text

Kinetics of papaya pectinesterase by Fayyaz, A., Asbi, B.A., Ghazali, H.M., Che Man, Y.B., Jinap, S.

“…The activity was linear up to 20 min with an enzyme concentration of up to 6.14 μg. …”
Get full text