Study on compressive properties of microwave cured composites by Yap, Yee Ling.

“…A study on the compressive properties of microwave cured glass fibre/epoxy composite has been carried out and the results are compared with those of thermally cured (autoclave) composites. …”
Get full text

Adhesive curing through low-voltage activation by Ping, Jianfeng, Gao, Feng, Chen, Jian Lin, Webster, Richard David, Steele, Terry W. J.

“…Instant curing adhesives typically fall within three categories, being activated by either light (photocuring), heat (thermocuring) or chemical means. …”
Get full text
Get full text

Bu ren 不忍 (Cannot bear to harm) in the Mencius by Sung, Winnie

Subjects: Get full text

Analysis of bull and bear phases of the Singapore stock market by Wang, Tiantian, Yang, Na

“…This project studies the alternation of bull and bear markets of Singapore stock market. Using historical daily Straits Time Index (STI) from 25/1/2000 to 24/8/2009 and weekly STI from 28/12/1987 to 24/8/2009, this project investigates two approaches to simulate the bull and bear runs, which are compared with the actual bull and bear runs. …”
Get full text

Experimental measurement of squeeze flow in hydrodynamics bearings by Xing, Fei

“…This project investigates the pressure generation performance by using 3 extended spiral grooves bearing (SGB), first one called K10 (new) with 10 grooves, second one called K15 (new) with 15 grooves, third one called K15 (Alan) with 15 grooves. …”
Get full text

Curing effect on the strength of cement mortar with bamboo biochar by Pragalanathan, Selvanathan, Pravina, K. Gunasekaran, Lai, Yeng Fock, Anand, N., Chin, Siew Choo

“…Additionally, it seeks to identify the optimal percentage of bamboo biochar in cement mortar to achieve optimal performance and determine the most effective curing method for cement mortar. The samples were subjected to curing for durations of 3 days, 7 days, and 28 days. …”
Get full text

Impact of peer review on reports of randomised trials published in open peer review journals : retrospective before and after study by Hopewell, S, Collins, G, Boutron, I, Yu, L, Cook, J, Shanyinde, M, Wharton, R, Shamseer, L, Altman, D

“…<br/><strong>Objective:</strong> To investigate the effectiveness of open peer review as a mechanism to improve the reporting of randomised trials published in biomedical journals. …”

Internalisation of externalities: who bears the cost of pollution control? by Rahim, Khalid Abdul

Get full text

Partially linear transformation cure models for interval-censored data by Hu, Tao, Xiang, Liming

Subjects: “…Cure rate…”
Get full text
Get full text

Numerical simulation and topology optimization of slider air bearing by Li, Qiang

“…Since the first commercial hard disk drive was developed in 1956, the stability of the flying attitude is always an important factor to be considered in the slider air bearing design. The objective of this dissertation is to develop an efficient computational modeling technique for simulating the air bearing slider (ABS) in hard disk drives and ultimately develop an effective topology optimization methodology to systematically and automatically design the air bearing slider with a target of achieving a near-constant flying attitude when the slider moves over the surface of the hard disk drive. …”
Get full text

Air bearing surface design for high flying stabilities by Lim, Choon Ming.

“…The purpose of the Air Bearing Surface (ABS) is to create an air cushion to allow the slider to fly over the platter disk at extreme low height without any physical contact. …”
Get full text

Simulation studies and experimental measurement of the air bearing slider by Ho, Jefferson Rui Ming.

Get full text

Study on electrical discharge machining (EDM) in motor bearings by Lam, Jin Seng

“…This research was put to the test with high gain and switching frequency for industrial grade motor bearing. Providing an understanding to how bearing damage occur. …”
Get full text

Analysis of UV cured 3D print of Phthalonitrile blends by Arunraj Chidambaram

“…In this report, the 3D printability of resorcinol-based phthalonitrile (RPN) was tested by mixing with a suitable photoresin (PR) binder that can be UV cured and afterwards thermally cured or carbonized. …”
Get full text

An Artificial Intelligence-Based Industry Peer Grouping System by Bonne, George, Lo, Andrew W, Prabhakaran, Abilash, Siah, Kien Wei, Singh, Manish, Wang, Xinxin, Zangari, Peter, Zhang, Howard

Subjects: Get full text
Get full text

Game theoretical, statistical and behavioural aspects of peer evaluation by Tan, Catherine Ser Ping

“…Another common concern with the current methods of peer evaluation is that students often do not have the necessary skills to evaluate the work of their peers objectively. …”
Get full text

Design and development of an online platform for peer tutorial scheme by Heng, Nadine Nyi Zheng

“…Notably, NTU’s School of Electronic and Electrical Engineering Student Life Development Unit SEENIORS Program, a relatively young peer tutoring scheme aimed at helping academically challenged students in school of EEE, currently only conducts its classes physically. …”
Get full text

Effects of peer pressure on endogenous goal setting and performance by Lim, Wee Meng, Chua, Shannen Qi Shan, Tan, Li Xuan

“…We investigate whether peer pressure has effects on endogenous goal setting and performance. …”
Get full text

Optimisation of silicon adhesive cure using differential scanning calorimetry analysis by Lee, Chow Sim.

“…Polymer curing is an essential part of electronic manufacturing process. …”
Get full text

Web-based application development for EEE peer tutoring scheme by Shan, Xinyi

Get full text