-
241
Innovative UWB phase shifters using groove gap-waveguide technology inspired by metasurfaces for beamforming networks operating at 100 GHz
Published 2025“…The metasurface features a "bed-of-nails" structure, where metal pins are connected to a bottom layer and spaced <λ/4 from a top plate. …”
Get full text
Conference or Workshop Item -
242
A study of touching behavior for authentication in touch screen smart devices
Published 2016“…Due to increasing demand for safer access in touch screen mobile phones, old strategies like pins, tokens, or passwords have failed to stay abreast of the challenges. …”
Get full text
Get full text
Proceeding Paper -
243
Metamaterial based ultra-wideband antennas for portable wireless applications
Published 2017“…Various approaches have been reported to reduce the physical size of RF antennas including using high permittivity substrates, shorting pins, reactive components, and more recently, metamaterials (MTM) based on composite right-/left-handed transmission-lines (CRLH-TLs). …”
Get full text
Book Section -
244
-
245
-
246
Ballistic impact fracture behaviour of continuous fibre reinforced al-matrix composites
Published 2010“…The materials response under high energy impact loads was studied using a gas gun. The projectiles were pins 1.2-1.5 mm in diameter and weighing 0.347-0.435 g. …”
Get full text
Article -
247
Modeling of a turning tool holder with finite elements and simulation of its free vibration frequencies
Published 2012“…This latter difference is unavoidable, due to the experimental test setup whereby the tool holder is clamped within the fixture with only 2 pins as opposed to the more rigid boundary condition applied to the finite element model, whereby the whole holder length within the carriage is rigidly supported at the element nodes. …”
Get full text
Article -
248
On phase separation points for one-dimensional models
Published 2009“…In the paper, the one-dimensional model with nearest-neighbor interactions In, n ∈ Z, and the s pin values ±1 is considered. It is known that, under some conditions on parameters of In, a phase transition occurs for this model. …”
Get full text
Article -
249
Measurement and modelling of operational amplifier power supply rejection
Published 1995“…Measured results for 741 and pin-compatible operational amplifiers are tabulated. …”
Get full text
Article -
250
Synthesis-condition dependence of carbon nanotube growth by alcohol catalytic chemical vapor deposition method
Published 2007“…Three types of heat-treatment, synthesis of 30 min, synthesis of 30 min after annealing of 30 min, and synthesis of 60 min, were investigated. …”
Get full text
Article -
251
Risk of Escherichia coli O157:H7 transmission linked to the consumption of raw milk
Published 2013Get full text
Article -
252
Distraction osteogenesis over intramedullary nail : a report of two cases
Published 2006“…The healing index was 19.5 days/cm and 14.8 days/cm respectively, compared favorably to 30 days/cm with traditional method of distraction osteogenesis. There were mild pin tract infections and joint stiffness which responded to non-operative treatment.…”
Get full text
Article -
253
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. …”
Get full text
Get full text
Article -
254
Characterisation of surface texture using AFM with trimmed probe tip
Published 2006“…A comparison of the scanning results with analytical calculation showed that the trimmed tips were superior in imaging the profile for both the hole shaped and pin shaped microfeatures. But when using the trimmed high aspect ratio tip, the scanning speed was significantly low. …”
Get full text
Article -
255
Cost-aware real-time divisible loads scheduling in cloud computing
Published 2024Get full text
Thesis -
256
Peranan guru besar, guru, dan, ibubapa mencapai objektif persekolahan sekolah rendah : perspektif ibu bapa
Published 2012“…Data respons dianalisis menggunakan perisian Statistical Package For The Social Sciences (SPSS) Version 16.0 dan dibentangkan dalam min. Kajian menunjukkan respons dimensi ’Perkembangan Asas Kendiri Murid’ mendapat skor tertinggi terhadap peranan guru dengan min 4.450, dimensi ‘Pembinaan Minat dan Bakat Murid’ skor tertinggi kepada peranan guru dengan min 4.212, dimensi ‘Persediaan Persekolahan Rendah’ skor tertinggi adalah ke atas peranan guru dengan min 4.374, dimensi ‘Persediaan Persekolahan Menengah’ skor tertinggi kepada peranan guru dengan min 4.374, dimensi ‘Pemahaman Budaya dan Kemahiran Sosial’ skor tertinggi kepada peranan guru dengan min 4.336, dimensi ’Keagamaan dan Moral’ skor tertinggi kepada peranan ibubapa dengan min 4.530, dimensi ‘Persediaan Pekerjaan’ skor tertinggi kepada peranan guru dengan min 4.352, dimensi ‘Sumbangan kepada Masyarakat’ skor tertinggi kepada peranan guru dengan min 4.503. …”
Get full text
Proceeding Paper -
257
Kinetics of water disinfection with Moringa Oleifera seeds extract
Published 2012“…One mL of Moringa extract was added to 10mL of the cell cultures and incubated for 0, 30min, 60min, 90min, and 120min without agitation. …”
Get full text
Article -
258
Sensory-based colour sorting automated robotic cell
Published 2005“…The aim of this research work is to recognize colour by pin point detection and sorting of object specimens with respect to their colour attributes, which includes hue, saturation and luminance level. …”
Get full text
Article -
259
A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
Published 2011“…Tool life sharply reduced for all the carbide tools while increasing cutting speed twice (from 500m/min to 1000m/min) during machining cast iron. Though the productivity would be double at the speed of 1000m/min than that at the speed of 500m/min, tool wear increases to a few times which indicates that the inserts used are not suitable for machining at a high speed like 1000m/min. …”
Get full text
Book Chapter -
260
Development and validation of analytical method by RP-HPLC for quantification of Alpha-Mangostin Encapsulated in PLGA microspheres
Published 2012“…Method was developed using a silica-based deactivated C-18 column (4.6×100 mm, 3 μm) with a mobile phase of 70-80 % v/v acetonitrile (A) and 0.1% v/v orthophosphoric acid (B), with the following pre-determined timed-gradient program: 70% (A) isocratic for 6 min, 70-75% (A) in 1.2 min, 75-80% (A) in 0.4 min, 80% (A) isocratic for 2.4 min, 80-70% (A) in 0.4 min, finally 70% (A)isocratic for 5 min, with a flow rate of 1 mL/min, detected at 320 nm by a UV detector. …”
Get full text
Article