Showing 1,341 - 1,360 results of 1,392 for search '((pine OR (pence OR (pinned OR (pina OR pingna)))) OR (peng OR ling))', query time: 0.16s Refine Results
  1. 1341

    NTU e-bike by Zeng, Wei

    Published 2011
    “…To support the touchscreen, the expansion board pin configurations are modified according to the schematic connections, also the kernel changed to detect the GPS device, the Éclair system can‟t get GPS information directly since a hardware abstraction layer (HAL) is needed for interacting between the Android framework and the kernel. …”
    Get full text
    Final Year Project (FYP)
  2. 1342
  3. 1343
  4. 1344
  5. 1345

    Analog smart I/O pads by Tan, Shyue Mei.

    Published 2009
    “…ESD is an increasingly significant problem in integrated circuit design as increasing pin counts and faster circuit speeds compound the need for more and better reliable ESD protection. …”
    Get full text
    Final Year Project (FYP)
  6. 1346
  7. 1347
  8. 1348

    Tribological properties of wax microcapsule modified polymers by Ang, Ping Lon

    Published 2013
    “…The tribology test uses the Pin-On-Disk wear test method and the default tribometer settings used in this project were set at 2000m sliding distance, 40cm/s linear speed and 3N linear load. …”
    Get full text
    Final Year Project (FYP)
  9. 1349
  10. 1350

    Conformable ultrasound breast patch for deep tissue scanning and imaging by Du, Wenya, Zhang, Lin, Suh, Emma, Lin, Dabin, Marcus, Colin, Ozkan, Lara, Ahuja, Avani, Fernandez, Sara, Shuvo, Ikra Iftekhar, Sadat, David, Liu, Weiguo, Li, Fei, Chandrakasan, Anantha P., Ozmen, Tolga, Dagdeviren, Canan

    Published 2024
    “…The in vitro studies and clinical trials reveal that the array using a piezoelectric crystal [Yb/Bi-Pb(In <jats:sub>1</jats:sub> <jats:sub>/2</jats:sub> Nb <jats:sub>1/2</jats:sub> )O <jats:sub>3</jats:sub> -Pb(Mg <jats:sub>1/</jats:sub> <jats:sub>3</jats:sub> Nb <jats:sub>2/3</jats:sub> )O <jats:sub>3</jats:sub> -PbTiO <jats:sub>3</jats:sub> ] (Yb/Bi-PIN-PMN-PT) exhibits a sufficient contrast resolution (~3 dB) and axial/lateral resolutions of 0.25/1.0 mm at 30 mm depth, allowing the observation of small cysts (~0.3 cm) in the breast. …”
    Get full text
    Article
  11. 1351
  12. 1352

    Developing a lightscape application (using a raspberry PI) by Ong, Wenchuan

    Published 2014
    “…The project aims to develop a web application, which will be hosted within the Raspberry Pi, for controlling the brightness of constant light source from the high power LED via the Raspberry Pi’s General Purpose Input Output (GPIO) pins and gather optimal settings for projecting images with the Light Blaster. …”
    Get full text
    Final Year Project (FYP)
  13. 1353

    Additive friction stir processing by Lin, Longyi

    Published 2014
    “…The continuous dynamic recrystalisation during FSP also gave finer grains, which was further enhanced with the addition of CNTs through Zener pinning effect. The improvement in tensile strengths due to finer grains through the Hall-Petch mechanism was insufficient to compensate for the drop in Orowan strengthening. …”
    Get full text
    Final Year Project (FYP)
  14. 1354
  15. 1355
  16. 1356
  17. 1357
  18. 1358

    Compatability and equilibrium approach to slender concrete column design (dual project) by Toh, Yi Hui

    Published 2017
    “…This report evaluates and compares the proposed design method with the Australian code AS3600-2001 for slender concrete column. The failure loads of pin-end columns under short term loading and uniaxial bending are used as a pre-determined factor to analyse the data. …”
    Get full text
    Final Year Project (FYP)
  19. 1359

    Local-flexural interactive buckling of S690 high strength steel slender welded I-section columns: testing, modelling and design by Sun, Yao, Liang, Yating, Su, Andi, Zhao, Ou

    Published 2022
    “…A testing programme, adopting two S690 high strength steel slender welded I-sections, was firstly conducted and included initial geometric imperfection measurements and ten pin-ended column tests. The testing programme was accompanied by a numerical modelling programme, where finite element models were developed and validated against the test results and then employed to perform parametric studies to generate further numerical data over a wide range of cross-section dimensions and member effective lengths. …”
    Get full text
    Journal Article
  20. 1360