-
261
Reverse engineering of automotive piston
Published 2012“…The wear test was performed using pin-on-disk (POD) machine. The tensile test results showed that the ultimate tensile strength and modulus of elasticity of the piston were 215 MPa and 73 GPa respectively, whereas the Vickers hardness number of this material was found to be 155 HV0.5kgf. …”
Get full text
Proceeding Paper -
262
Electronically reconfigurable and conformal triband antenna for wireless communications systems and portable devices
Published 2022“…This is achieved by connecting two open-ended stubs to a modified triangular patch radiator using PIN diodes. The antenna’s performance was optimized using a 3D electromagnetic solver and its performance was verified through measurements. …”
Get full text
Get full text
Article -
263
The effect of milling parameters on laminated carbon fibre reinforced plastic (CFRP)
Published 2012“…A solid uncoated carbide end mill cutting tool and a CFRP panel with fibre orientation of 0/45° were used to investigate the machinability of CFRP composite during milling; a cutting speed of 16 m/min to 240 m/min with a feed rate of 0.0125 mm/tooth to 0.0125 mm/tooth were set. …”
Get full text
Article -
264
-
265
A comparative study of the effectiveness of ca-alginate and k-carrageenan beads as support material for enzyme immobilization
Published 2015“…Michaelis parameters Vmax and KM for Ca-alginate were found to be 65.36 mmol/min and 8.60 mM respectively, and for K-carrageenan 61.73 mmol/min and 0.94 mM respectively, while Michaelis constants for the free enzyme were 70.42 mmol/min and 2.71 mM. …”
Get full text
Get full text
Proceeding Paper -
266
Photocatalytic degradation of triclocarban in aqueous solution using a modified zeolite/TiO2 composite: kinetic, mechanism study and toxicity assessment
Published 2023“…The kinetic study by following Langmuir-Hinshelwood(L-H) model and pseudo first order, the significant constant rate was obtained at pH 11 which was 0.079 ppm/min, 0.75 cm2 of MZTC catalyst loading size achieved 0.076 ppm/min and 5 ppm of TCC initial concentration reached 0.162 ppm/min. …”
Get full text
Article -
267
Faktor yang mendorong kecenderungan pelajar kolej vokasional ke arah bidang keusahawanan
Published 2014“…Dapatan menunjukkan skor min bagi faktor kemahiran, sikap dan latar belakang pendidikan pada tahap tinggi iaitu masing-masing 4.02, 4.04 dan 3.93. …”
Get full text
Get full text
Thesis -
268
Ciri-ciri yang mempengaruhi pelatih aliran kemahiran untuk menjadi seorang usahawan : satu tinjauan di Institut Kemahiran Mara Lumut, Manjung Perak
Published 2003“…Data-data kajian dianalisa dengan menggunakan program SPSS Versi 11.0 for windows dan dianalisis daripada soal selidik ke dalam bentuk min dan frekuensi. Keseluruhan hasil kajian menunjukkan bahawa pelatih-pelatih mempunyai ciri-ciri keusahawanan yang tinggi berdasarkan skor min keseluruhan (skor min = 4.06). …”
Get full text
Get full text
Get full text
Thesis -
269
How to assess ankle osteoarthritis: comparison of the Kellgren and Lawrence scale with functional outcome and digital image analysis
Published 2012“…Functional outcome was assessed with the AOFAS Hindfoot score. Bone density and minJSW were measured using a previously validated Ankle Image Digital Analysis software (AIDA). …”
Get full text
Article -
270
-
271
Mas Cotek (Ficus deltoidea): a possible supplement for Type II Diabetes: (a pilot study)
Published 2011Get full text
Book Chapter -
272
Non-invasive measurement method of skin conditions by using Dermalab® combo
Published 2014“…The readings were taken on volar forearm of the volunteers were taken using TEWL probe and hydration pin probe. A set of questionnaire was also distributed to obtain the information about the skin care regime and their daily habits. …”
Get full text
Proceeding Paper -
273
Providing feedback for students' drafts in academic writing: can developmental Rubric do the trick?
Published 2015“…Teachers were able to specifically pin-point the areas where students needed to improve their academic writing. …”
Get full text
Proceeding Paper -
274
Formation of Fe-C-Si ternary composite coating on CP-titanium and its tribological interaction with Jatropha oil
Published 2016“…The wear behavior of coated CP-titanium was performed using pin-on-disk machine at room temperature under Jatropha-biodiesel lubricated condition. …”
Get full text
Proceeding Paper -
275
A Novel MIMO antenna integrated with a solar panel and employing AI-equalization for 5G wireless communication networks
Published 2024“…We demonstrate that the directivity of this antenna array can be precisely electronically reconfigured using PIN diode switches. Additionally, we show the feasibility of integrating solar panels with the proposed MIMO antenna array. …”
Get full text
Get full text
Article -
276
Design of microstrip ultra wide band antenna with two notch filters for wireless communication
Published 2015“…In order to add reconfigurable characteristics to the patch antenna, two copper strips are putted on the slots to represent the ON and OFF switching status of an ideal Pin diode. By using this simple switching technique, the current distribution of the patch changes and enables the antenna to have four modes of operation. …”
Get full text
Get full text
Get full text
Thesis -
277
Theoretical analysis of photoparametric amplifier
Published 2010“…The second method is to use Optiwave software in implement is the photo parametric amplifier circuit. Photo diode PIN type has been used to detect any coming signal at the receiver circuit. …”
Get full text
Get full text
Get full text
Thesis -
278
Ultrasound-assisted extraction of valuable compounds from winter melon (Benincasa hispida) seeds
Published 2013“…Effects of amplitude (25-75%), temperature (40-60°C) and sonication time (20-60 min) on crude extraction yield (CEY) and radical scavenging activities (RSA, % inhibition of DPPH˙ and ABTS˙+ free radicals) of extracts were determined using complete randomised design (CRD). …”
Get full text
Article -
279
High performance liquid chromatographic method for Iso-a-Acids
Published 2006“…The mobile phase contains acetonitrile-water- H3PO4 (50 : 50 : 0.01, v/v/v) and is used with a Phenomenex Hypersil 5 m C18 column 250 � 4.6 mm, flow rate 1.5mL/min. Baseline separation of all 6 isomers was achieved with a total run time of 25 min. …”
Get full text
Article -
280
Microstructure and tensile properties of friction stir processed Al-Si alloy
Published 2018“…Samples were subjected to FSP using fixed tool rotation speed 1400 rpm and traverse speed 42 mm/min, with tool angle tilted 3˚.The influence of the FSP on the microstructure and tensile properties of the cast AlSi-Cu-Ni alloy samples were studied. …”
Get full text
Article