-
181
The tribological behaviour of Fe-C-Al cast iron – effect of temperature
Published 2013“…The wear and friction tests were conducted using universal pin-on-disk machine at 25 0C, 100 0C, 200 0C and 300 0C temperature. …”
Get full text
Article -
182
Low-loss paper-substrate triple-band-frequency reconfigurable microstrip antenna for sub-7 GHz applications
Published 2023“…In this paper, a low-cost resin-coated commercial-photo-paper substrate is used to design a printed reconfigurable multiband antenna. The two PIN diodes are used mainly to redistribute the surface current that provides reconfigurable properties to the proposed antenna. …”
Get full text
Get full text
Article -
183
Development of a low cost lapping process
Published 2009“…Therefore the understanding of lapping process is very essential for economic manufacture and process improvement of thin silicon chips. A low cost lapping process has been developed, the process tried out on thin silicon chips that generated damage-free with a mirror-like surfaces of low roughness values and reasonably high degree of flatness.…”
Get full text
Proceeding Paper -
184
Manufacture of cylinders with axial imperfections
Published 2004“…The report outlines the methodology and procedures used to manufacture the thin walled cylinder with its axial imperfections using a NUM 1060 CNC Lathe machine. …”
Get full text
Thesis -
185
Performance analysis of two packet scheduling algorithms in downlink 3GPP LTE system
Published 2010Get full text
Get full text
Proceeding Paper -
186
Development of low coast atmospheric pressure plasma jet for nano and bio technology applications
Published 2018“…The wettability of Aluminium (Al) thin film was enhanced from 72° to 0°. The topography studies indicated that treated Al thin film surface roughness reduced by 2.86 X10-3 nm but the grain size was unaffected. …”
Get full text
Get full text
Get full text
Thesis -
187
Development of an economical lapping process
Published 2012“…This paper presents the development of a low cost lapping process, the process tried out on thin silicon chips that generated fracture-free with mirror-like surfaces of low roughness values and reasonably high degree of flatness.…”
Get full text
Article -
188
The optical properties of oxide films on copper and copper alloys
Published 1985“…Suitable conditions were selected to allow thin, thermal oxide films consisting of cuprous oxide only to be grown on copper and dilute copper alloy substrates. …”
Get full text
Thesis -
189
Requirement of handover modeling in the downlink 3GPP long term evolution system
Published 2010Get full text
Get full text
Proceeding Paper -
190
On phase separation points for one-dimensional models
Published 2009“…In the paper, the one-dimensional model with nearest-neighbor interactions In, n ∈ Z, and the s pin values ±1 is considered. It is known that, under some conditions on parameters of In, a phase transition occurs for this model. …”
Get full text
Article -
191
Measurement and modelling of operational amplifier power supply rejection
Published 1995“…Measured results for 741 and pin-compatible operational amplifiers are tabulated. …”
Get full text
Article -
192
Investigation on plasma properties for deposition of titanium nitride film using reactive magnetron sputtering system
Published 2018“…However, formation of TiN thin flms in nano size device using the plasma sometimes is not stable and hard to achived with optimum level. …”
Get full text
Get full text
Get full text
Thesis -
193
Features of EDM of mild steel with Ta-Cu powder compacted electrodes
Published 2011“…On the contrary, there will be only a very thin layer of material from electrode will be deposited on the workpiece surface when using pure copper electrode. …”
Get full text
Book Chapter -
194
Borderline personality disordered clients' experience and understanding of therapeutic boundaries: a Q methodogical study
Published 2010“…Fluctuation between thick and thin boundaries. D. "BRICK WALL": Participants assumed a position that was rigid, emotionally and/or physically distant. …”
Get full text
Thesis -
195
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…This paper presents a novel metasurface antenna whose radiation characteristics can be remotely controlled by optical means using PIN photodiodes. The proposed reconfigurable antenna is implemented using a single radiating element to minimize the size and complexity. …”
Get full text
Get full text
Article -
196
Characterisation of surface texture using AFM with trimmed probe tip
Published 2006“…A comparison of the scanning results with analytical calculation showed that the trimmed tips were superior in imaging the profile for both the hole shaped and pin shaped microfeatures. But when using the trimmed high aspect ratio tip, the scanning speed was significantly low. …”
Get full text
Article -
197
Distraction osteogenesis over intramedullary nail : a report of two cases
Published 2006“…The healing index was 19.5 days/cm and 14.8 days/cm respectively, compared favorably to 30 days/cm with traditional method of distraction osteogenesis. There were mild pin tract infections and joint stiffness which responded to non-operative treatment.…”
Get full text
Article -
198
Chemoreception and vertical movement in planktonic yolk-sac larvae of red sea bream Pagrus major
Published 1991“…After infrequent vertical burst swimming followed by slight rising or sinking, the larvae remained motionless within thin layers of concentrated food extract (rotifer, Brachionus plicatilis). …”
Get full text
Article -
199
-
200
Reduced graphene oxide-multiwalled carbon nanotubes hybrid film with low Pt loading as counter electrode for improved photovoltaic performance of dye-sensitised solar cells
Published 2018“…TC14-rGO and TC14-rGO_MWCNTs hybrid solution were transferred into fluorine-doped tin oxide substrate to fabricate thin film by spraying deposition method. Finally, the CE films were prepared by coating with thin Pt NPs. …”
Get full text
Article