Showing 1,201 - 1,220 results of 2,309 for search '((pinnau OR (pinn OR (financed OR ((pingd OR pings) OR ping)))) OR ((aina OR ainaa) OR min))', query time: 0.19s Refine Results
  1. 1201
  2. 1202
  3. 1203
  4. 1204
  5. 1205
  6. 1206
  7. 1207
  8. 1208
  9. 1209
  10. 1210
  11. 1211
  12. 1212
  13. 1213

    Laser metal deposition of low carbon 410L stainless steel and heat treatment by Zhai, Wengang, Wu, Naien, Zhou, Wei

    Published 2023
    “…The yield strength is 601.9 MPa for as-built condition and 930.6 MPa for heat-treated condition (1000 °C/10 min); the ultimate tensile strength (UTS) is 923.0 MPa for as-built condition and 1101.5 MPa for the heat-treated condition (1000 °C/10 min); the elongation is 17.7% for as-built condition and 15.1% for the heat-treated condition (1000 °C/10 min). …”
    Get full text
    Journal Article
  14. 1214

    Dose response effect of carbohydrate mouth rinse on 10 km running time trial by Muhammad Saufy Abdul Karim

    Published 2018
    “…Results: No significant difference (p = .441) in 10 km running time trial were observed between 6.4% CHO [mean 63.83 (SD 11) min] and 15% CHO [mean 65.91 (SD 13.36) min]. No significant difference were found in HR (p = .440) between 6.4% CHO [mean 162 (SD 7) beats/min] and 15% CHO [mean 158 (SD 13) beats/min]. …”
    Get full text
    Final Year Project (FYP)
  15. 1215

    Pengetahuan, Sikap dan Praktis (KAP) Komuniti Pekebun Kecil Koko (KPKK) berkaitan Malaysian Good Agricultural Practices (MyGAP) by Noviatin Syarifuddin, Jasmin Arif Shah, Asnarulkhadi Abu Samah, Nik Ahmad Sufian Burhan

    Published 2024
    “…Tahap amalan pertanian baik (APB) menunjukkan nilai min tertinggi oleh praktis (min 4.20). Diikuti, dengan tahap sikap (min 4.08) dan tahap pengetahuan (min 4.01) oleh KPKK. …”
    Get full text
    Article
  16. 1216

    Mechanical properties of pultruded Kenaf fibre-reinforced vinyl ester composites by Abd Manab, Mohd Fairuz

    Published 2016
    “…The investigation of the effect of pulling speed on the mechanical properties of pultruded kenaf composites shows the optimal pulling speed for tensile strength and compressive strength is 0.3 m/min, tensile modulus 0.1 m/min, flexural strength 0.4, flexural modulus 0.2 m/min. …”
    Get full text
    Thesis
  17. 1217

    Influence of machining parameters and tool geometry on tool wear during cobalt chromium-molybdenum micro drilling by Abdul Patar, Mohd. Affifudin, Suhaimi, Mohd. Azlan, Sharif, Safian, Amrifan S. Mohruni, Amrifan S. Mohruni, Hisam, Muhammad Juzaili, Shaharum, Mohd. Sallehuddin

    Published 2024
    “…The cutting speeds of 50 m/min, 65 m/min, and 80 m/min were varied. A total of 11 runs were performed, with each run consisting of drilling 30 holes. …”
    Get full text
    Article
  18. 1218
  19. 1219
  20. 1220