-
21
-
22
Disturbance decoupled fault reconstruction using sliding mode observers
Published 2008Get full text
Proceeding Paper -
23
Preliminary design of sliding mode controller for angular positional tracking of an aircraft
Published 2009Get full text
Proceeding Paper -
24
-
25
Comparison of biometrics industry between Malaysia and India: an overview
Published 2011Get full text
Article -
26
The Use of i-THINK Mapping in Teaching Reading Comprehension among ESL Teachers
Published 2023Get full text
Article -
27
The Use of i-THINK Mapping in Teaching Reading Comprehension among ESL Teachers
Published 2023Get full text
Article -
28
-
29
The Use of i-THINK Mapping in Teaching Reading Comprehension among ESL Teachers
Published 2023Get full text
Article -
30
Bulk α-alumina embedded tapered fiber as Q-switcher in an erbiumdoped fiber laser
Published 2024Get full text
Article -
31
-
32
A parametric study of DMS subjected to induced low-stress consolidation and heat treatment
Published 2020“…DMS consists mainly of clays, silts and sand mingled with rocks, debris, larger obstacles and organic matter such as polycyclic aromatic hydrocarbons (PAHs) and polychlorinated aromatic biphenyl (PCBs)…”
Get full text
Book Section -
33
British and Irish Diasporas: Societies, cultures and ideologies
Published 2018“…People from the British and Irish Isles have, for centuries, migrated to all corners of the globe.Wherever they went, the English, Irish, Scots, Welsh, and and even sub-national, supra-regional groups like the Cornish, co-mingled, blended and blurred. Yet while they gradually integrated into new lives in far-flung places, British and Irish Isle emigrants often maintained elements of their distinctive national cultures, which is an important foundation of diasporas. …”
Book -
34
Antivirals for broader coverage against human coronaviruses
Published 2024“…Spike is also not applicable for targeting other HCoVs as these are not well-conserved sequences among human CoVs. …”
Get full text
Article -
35
Novel opto-electronic and plastic fibre sensors
Published 1998“…The middle POF is coupled to a red LED and emits light onto a flat target with the two outer fibres receiving the reflected light from the target and guiding it to two silicon PIN photodiodes. Theoretical investigations on the behaviour of the sensor are presented for ranges between 0 mm and 100 mm, and for targets with different reflectivities. …”
Get full text
Thesis -
36
Development of switchable planar reflectors for beam shaping realization
Published 2016“…Higher tunable loss factor of 1.91dB was demonstrated by liquid crystal based design as compared to tunable loss factor of 1.43dB shown by PIN diode based design. The investigations were further extended by carrying out equivalent circuit analysis of PIN diode based and liquid crystal based designs for detailed characterization of reconfigurable planar reflector designs. …”
Get full text
Get full text
Get full text
Thesis -
37
Characterization of cyclic plasticity type wear mechanism for titanium alloy, TI-6AL-4V on reciprocating sliding wear test
Published 2020“…Meanwhile for the contact pin, two different diameter cylinders are used i.e Ø6.5 mm and Ø12 mm. …”
Get full text
Get full text
Get full text
Thesis -
38
Electrical breakdown and structural characterization in synthetic resins using optical techniques
Published 1992“…The early tree growth is shown to be driven by the high electrical field near the pin tip, which is itself dependent on the pin-plane electrode separation as well as the applied voltage. …”
Get full text
Thesis -
39
Evaluation of classifiers in a pressure and latency-based typing biometric system
Published 2011“…System authentication in present time relies on validation by some sort of a password or Personal Identification Number (PIN). However, if an intruder discovers this password or PIN, the user’s account can be easily compromised. …”
Get full text
Proceeding Paper -
40
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…The later has been attributed to failure occurring at the pin tip epoxy interface causing relaxation in the scattering volume. …”
Get full text
Thesis