-
261
Influence of single and multiple particle size variation on mechanical and wear behaviour of aluminium silicon carbide composites
Published 2015“…Standard impact and hardness test was conducted to ascertain the energy absorbed before fracture failure and resistance to plastic deformation of the composite. Pin-on-disc test was also investigated at room temperature under dry sliding wear condition. …”
Get full text
Proceeding Paper -
262
Frequency reconfigurable substrate integrated waveguide (SIW) cavity F-shaped slot antenna
Published 2019“…Configurability is accomplished by embeddings PIN diode switches in the 'F' slot. The proposed antenna is equipped for exchanging between working band of 3.172 GHz to 3.606 GHz in four different narrow bands and it underpins the cognitive system for LTE2300, WiMAX and WLAN. …”
Get full text
Article -
263
Performance evaluation of uncoordinated beamforming over cognitive radio network
Published 2012“…We present the optimum weight design to maximize the SINR and achievable sum rate for both primary and cognitive link under the condition that the cross interference at both receivers are totally nullified. …”
Get full text
Get full text
Proceeding Paper -
264
Primary ewing's sarcoma of the lumbosacral spine : a case report
Published 2012“…Among soft tissue Ewing's, spinal cord involvement is rarer with only nine cases reported. …”
Get full text
Article -
265
Phase diagrams of a Potts Model with competing binary and ternary interactions
Published 2010Get full text
Proceeding Paper -
266
Remote operation of CNC milling through virtual simulation and remote dekstop interface
Published 2009“…Capability of remote operation is supported by an auto setup attachment with a reconfigurable pin type setup free technology installed on the table of CNC milling machine to perform unattended machining process. …”
Get full text
Article -
267
Aluminium metal matrix composite: improving wear performance through treatment
Published 2011“…The wear test was carried out using a pin-on- disc type tribo-test machine under dry sliding condition. …”
Get full text
Article -
268
Wear behavior of modified surface layer produced by TIG melting of preplaced Ti powder in nitrogen environment
Published 2011“…The wear property of the melt track was investigated using pin-on-disk tribometer at room temperature. The modified surface layer gave a low friction value of 0.12 and wear rate of 0.007895 ×10-4 compared to 1.648 × 10-4 mm3/N/m for the uncoated steel surface.…”
Get full text
Article -
269
Recovery of virus producing NDV vaccine by Tangential Flow Filtration (TFF)
Published 2009“…The results revealed that higher pressure input (Pin), lower pressure output (Pout), and higher virus concentration led to higher virus titer. …”
Get full text
Proceeding Paper -
270
Wear properties of Fe-C-Al cast iron and conventional cast iron - a comparative study
Published 2011“…In the present study, the wear test was conducted on both conventional cast iron (CI) and Fe-C-Al cast iron using universal pin-on-disk (POD) machine. The wear track profile and damage surface were characterized using optical profilometer and scanning electron microscopy (SEM) respectively. …”
Get full text
Proceeding Paper -
271
Microelectrical mechanical systems switch for designing multi-band antenna
Published 2009“…Problem statement: In this study Microelectrical Mechanical System (MEMS) switches were proposed to design a reconfigurable/multi-band antenna to replaced PIN diode switches or semiconductor switches due to lower insertion losses, good isolation, much lower intermodulation distortion, and lower power consumption. …”
Get full text
Article -
272
Smart home control system design using internet of things based energy harvesting technology
Published 2024“…The objective of this research is to provide security for homeowners by facilitating fingerprints and PIN (Personal Identification Numbers) in entering the house, then in the event of a power outage, it activates the function of energy harvesting technology. …”
Get full text
Conference or Workshop Item -
273
-
274
In-Utero effects of the crude ethanolic extract of the leaves of mitragyna speciosa on neural tube formation in rats
Published 2010“…Results indicate that the medium (C) and high (D) (1000 & 1500mg/kg) doses but not the low (B) (500mg/kg) dose in comparison with control (A) group, significantly (p10.001) produced a widening of the vertebral arch in the thoracic, lumber and cervical regions of the spinal cord. The brain transverse diameter was also significantly (p10.05) increased by the high dose only. …”
Get full text
Article -
275
Biomechanical Study of Posterior Lumbar Interbody Fusion: A Review
Published 2023“…Degenerative disc disease is a spinal disorder in which the vertebral disc helps protect nerves and increase spine flexibility that begins to deteriorate. …”
Get full text
Article -
276
Biomechanical Study of Posterior Lumbar Interbody Fusion: A Review
Published 2023“…Degenerative disc disease is a spinal disorder in which the vertebral disc helps protect nerves and increase spine flexibility that begins to deteriorate. …”
Get full text
Article -
277
Biomechanical Study of Posterior Lumbar Interbody Fusion: A Review
Published 2023“…Degenerative disc disease is a spinal disorder in which the vertebral disc helps protect nerves and increase spine flexibility that begins to deteriorate. …”
Get full text
Article -
278
Biomechanical Study of Posterior Lumbar Interbody Fusion: A Review
Published 2023“…Degenerative disc disease is a spinal disorder in which the vertebral disc helps protect nerves and increase spine flexibility that begins to deteriorate. …”
Get full text
Article -
279
The effect of palm oil diesel fuel contaminated lubricant on sliding wear of cast irons against mild steel
Published 1996“…This was done on three types of cast iron, namely spheroidal graphite, flake graphite and chilled cast iron against a mild steel disc configuration using a pin-on-disc type of friction and wear apparatus. …”
Get full text
Article -
280
Virtual simulation and remote desktop interface for CNC milling operation
Published 2011“…Capability of remote operation is supported by an auto setup attachment with a reconfigurable pin type setup free technology installed on the table of CNC milling machine to perform unattended machining process. …”
Get full text
Article