Showing 1,301 - 1,320 results of 3,663 for search '((sine OR (pinge OR line)) OR (((mings OR min) OR (shing OR sspinal)) OR pin))', query time: 0.23s Refine Results
  1. 1301

    Enhancing Performance of Private Higher Education Institution through Strategic Excellence Model (S/O 13617) by Abdullah, Haim Hilman

    Published 2020
    “…In the context of Malaysia, education has been earmarked as one of the important national agenda in line with the 11th Malaysia. Plan that is designed to make the country a knowledge-based economy. …”
    Get full text
    Monograph
  2. 1302
  3. 1303
  4. 1304
  5. 1305
  6. 1306

    Evaluation of carob tree (Ceratonia siliqua L.) pods, through three different drying techniques, and ultrasonic assisted extraction, for presence of bioactives by Hussain, Ashiq, Arif, Muhammad Rehan, Ahmed, Adnan, Laaraj, Salah, Firdous, Nida, Ali, Muhammad Qasim, Haya Fatima, ., Yaqub, Shazia, Kauser, Samina, Nisar, Rizwan, Gorsi, Faiza Iftikhar, Ud Din, Ghulam Mueen, Elfazazi, Kaoutar

    Published 2024
    “…The purpose of this study was to determine how ethanolic extracts of carob pods from Morocco, prepared with ultrasonic assistance were affected by microwave (525 °C for 2.5 min), hot air (65 °C for 16 h), and spray drying (input and output air temperatures 180 and 90 °C, respectively, feed flow rate 2.5 mL/min and 5 bars, respectively), in terms of their physicochemical composition and biological activity. …”
    Get full text
    Get full text
    Article
  7. 1307

    Biotin-streptavidin binding interactions of dielectric filled silicon bulk acoustic resonators for smart label-free biochemical sensor applications by Heidari, Amir, Yoon, Yong-Jin, Park, Woo-Tae, Su, Pei-Chen, Miao, Jianmin, Park, Mi Kyoung, Lin, Julius Tsai Ming

    Published 2014
    “…The resonance frequency of the biotin modified resonator decreased 315 ppm when exposed to streptavidin solution for 15 min with a concentration of 10−7 M, corresponding to an added mass of 3.43 ng on the resonator surface. …”
    Get full text
    Get full text
    Journal Article
  8. 1308
  9. 1309

    Elucidation of thermally induced internal porosity in zinc oxide nanorods by Handoko, Albertus D., Liew, Laura-Lynn, Lin, Ming, Sankar, Gopinathan, Du, Yonghua, Su, Haibin, Dong, Zhili, Goh, Gregory Kia Liang

    Published 2020
    “…A manageable pore growth rate of 1.4–4.4 nm3·min−1 was observed at 540 °C, suggesting that the effective control over internal porosity can be achieved by carefully controlling the heat-treatment profile. …”
    Get full text
    Journal Article
  10. 1310
  11. 1311

    Temperature and stress distribution in the SOI structure during fabrication by Tan, Cher Ming, Gan, Zhenghao, Gao, Xiaofang

    Published 2009
    “…Although it is expected that the furnace temperature and withdrawal velocity are the key factors in determining the mechanical stresses, for the present bonding strength of wafers via wafer bonding technology, the withdrawal velocity must be less than 100 mm/min, and under such a withdrawal velocity, the furnace temperature is also an insignificant factor with regard to the induced stress.…”
    Get full text
    Get full text
    Journal Article
  12. 1312

    Electron beam grafted Polyethylene/Polypropylene fibers: a novel approach to amine-functionalized adsorbents for Naproxen removal by Yusoff, Nor Aida, Abdullah, Luqman Chuah, Md. Jamil, Siti Nurul Ain, Ting, Teo Ming, Zainuddin, Halimatun Sakdiah

    Published 2024
    “…Notably, even at a low amine-to-isopropanol ratio (30 %) using EDA, the adsorbents achieved a high naproxen removal rate of 96.90 % within 90 min and an adsorption capacity of 247.10 mg/g, surpassing the performance of the DAP-modified (PE/PP)-g-GMA. …”
    Get full text
    Article
  13. 1313

    Solution based synthesis of Cu2ZnSnS4 nanoparticles and thin films for solar cell application by Li, Zhenggang

    Published 2014
    “…CZTS nanoparticles formed immediately after injection of S precursor. From 0 min to 30 min, the average size of the nanoparticles gradually increased and the size distribution became narrower. …”
    Get full text
    Thesis
  14. 1314
  15. 1315
  16. 1316
  17. 1317

    Microstructural inhomogeneity of a 3D-printed nickel aluminium bronze by Tan, Yi Xuan

    Published 2022
    “…Different printing speeds of 0.5,1 and 2m/min will be applied to prepare samples with inhomogeneous microstructure using laser metal deposition. …”
    Get full text
    Final Year Project (FYP)
  18. 1318
  19. 1319
  20. 1320