-
561
Breast cancer detection based on simplified deep learning technique with histopathological image using BreaKHis database
Published 2023“…This is followed by applying transfer learning techniques in the deep convolutional networks like ResNet, ResNeXt, SENet, Dual Path Net, DenseNet, NASNet, and Wide ResNet. …”
Get full text
Get full text
Article -
562
-
563
-
564
A study of microwave induced plasmas
Published 1987“…Two 'analytical' MIP's incorporating sample aerosol introduction have been used with the slab-line cavity. One being supported on an argon flowrate of 0.1 1 min-1 using a Babing!…”
Get full text
Thesis -
565
Wear characteristics of Fe-C-Si and Fe-C-Al cast irons
Published 2011“…Alumina ball of 3 mm diameter was used as pin, while the cast sample served as the disk. The tests were carried out at a normal load of 5.0 N and a sliding velocity of 250 mm/s for 30 min. …”
Get full text
Article -
566
Signature recognition using artificial neural network
Published 2011“…Automatic handwritten signature verification is divided into two approaches: off-line and on-line. In the off-line signature verification approach, the data of the signature is obtained from a static image utilizing a scanning device [I). …”
Get full text
Book Chapter -
567
Penerimaan pembelajaran berasaskan permainan digital dalam mempengaruhi motivasi belajar
Published 2020“…Analisis data melibatkan analisis kekerapan, skor min, sisihan piawaian dan peratusan menggunakan perisian SPSS 20. …”
Get full text
Book Section -
568
An investigation of defect formation and growth in epoxy resin using light scattering methods
Published 1989“…This suggests a possible link in the deformation processes under either stress. …”
Get full text
Thesis -
569
An experimental approach to determine the critical depth of cut in brittle-to-ductile phase transition during end milling of soda lime glass
Published 2016“…A two-fluted solid end mill of 4 mm diameter was used with cutting speed ranging from 377 to 628 m/min and feed rate from 5 to 20 mm/min to investigate the phenomenon of transition from plowing to ductile and ductile to brittle machining mode. …”
Get full text
Get full text
Get full text
Article -
570
-
571
Exploring the potential of the recombinant human collagens for biomedical and clinical: a short review
Published 2021“…HLC was initially used as a coating to modify the tissue engineering scaffold, and then used as the scaffold after cross link agents were added to increase its mechanical strength. …”
Get full text
Article -
572
-
573
Unusual association of diseases/symptoms: Sweet's syndrome in Crohn's colitis
Published 2009“…We would like to report a case involving a 38-year-old woman who presented with knee and ankle swellings 2 weeks prior to admission. …”
Get full text
Article -
574
Development of coated peanut separator and frying skillet machine
Published 2018“…The groundnut is sticking and become like a ping pong size ball and the time consuming to fry is longer. …”
Get full text
Article -
575
Photonic controlled metasurface for intelligent antenna beam steering applications including 6G mobile communication systems
Published 2023“…The metasurface layer is a lattice pattern of square framed rhombus ring shaped unit-cells that are interconnected by PIN photodiodes. The metasurface layer essentially acts like a superstrate when exposed to RF/microwave radiation. …”
Get full text
Get full text
Article -
576
A comparative study on flank wear and work surface finish during high speed milling of cast iron with different carbide tools
Published 2011“…Tool life sharply reduced for all the carbide tools while increasing cutting speed twice (from 500m/min to 1000m/min) during machining cast iron. Though the productivity would be double at the speed of 1000m/min than that at the speed of 500m/min, tool wear increases to a few times which indicates that the inserts used are not suitable for machining at a high speed like 1000m/min. …”
Get full text
Book Chapter -
577
Sensory-based colour sorting automated robotic cell
Published 2005“…The aim of this research work is to recognize colour by pin point detection and sorting of object specimens with respect to their colour attributes, which includes hue, saturation and luminance level. …”
Get full text
Article -
578
Bio-inspired snake robot locomotion: a CPG-based control approach
Published 2015“…Natural control generates motion instantly based on the feelings from the environment. In line with this concept, an artificial control system is known as Central Pattern Generator (GPG) is an online motion generation system that can be generated instantly like spine based control system. …”
Get full text
Get full text
Proceeding Paper -
579
Preliminary analysis on the effect of rain attenuation on Free Space Optics (FSO) propagation measured in tropical weather condition
Published 2011“…Non-selective scattering is wavelength independent and exists due to rainfall. In country like Malaysia rain season with heavy rain can reduce the received power of FSO link to below the threshold. …”
Get full text
Proceeding Paper -
580
Fatty acid compositions of fish oil extracted from different parts of Indian mackerel (Rastrelliger kanagurta) using various techniques of supercritical CO2 extraction
Published 2010“…Fatty acid compositions of fish oil extracted from different parts of Indian mackerel (Rastrelliger kanagurta) using various techniques of supercritical carbon dioxide (SC-CO2) at optimised conditions (35 MPa, 60 �C, 2 ml/min) were analysed and compared to the results of Soxhlet extraction. …”
Get full text
Article